User manual MITSUBISHI PHOTO ID SYSTEM DIS 710

[. . . ] Printer MONITOR MEMORY PRINT Options (not provided from Mitsubishi) ALARM SHEET PAPER S-VIDEO POWER OPEN REMOTE · AC cable · Operation manual · Ink cassette Printer System Monitor Tripod Camera Connection box · System cable · Operation manual · 3 guide sheets · Print paper and ink sheet Strobe This system complies with the requirements of the EC Directive 89/336/EEC "EMC Directive" as amended by Directive 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system. 2 1. SAFETY PRECAUTIONS In the interest of safety, please observe the following precautions: POWER REQUIREMENT This system is designed for operation on 220V-240V, 50Hz AC. [. . . ] Then, set the paper roll on the left side paper holder. Right side Print paper Holder Install Left side Holder 3 Insert the print paper between roller 1 and 2. 4 Insert the edge of the print paper to roller 3. Be sure to insert the paper straight. Roller Roller Roller 3 Print paper Roller Roller 2 Roller 1 Paper Paper Paper INCORRECT CORRECT INCORRECT Print paper 5 Feed the print paper through the exit slot straight with your hand. 6 Pull the print paper to eliminate slack. NOTE If too much paper is fed, an error may occur. ("PAPER JAM12" is indicated on the monitor screen. ) In this case, press the MEMORY button while holding the MONITOR button for a second. 7 Move the knob on the side of the printing unit to the direction as indicated by the arrow. 1 8 INSTALLING THE INK SHEET White roller Install the ink cassette with the ink sheet rolls before inserting the ink cassette into the printer. E B C 1 Put the colored roller of the ink sheet to the ink cassette. DE On the position, turn the roller and set the notch of the roller side to the hole of the cassette. The roller can be installed when notch is put through the hole. B A Colored roller E D D notch 1 Eliminate any slack of the ink sheet. Hold the roller INSTALLING THE INK CASSEETTE A and B and turn the white roller. A B 2 Insert the ink cassette with the ink sheet into its compartment. Insert the ink cassette with the knob side toward you until it is locked into place. · When taking the ink cassette out of the compartment, press the ink cassette locking holder to release the lock. 1 Push the printing unit until it is locked into place. 2 After plugging the power cord, press POWER button on the front panel. SET THE PRINTING UNIT 3 Press the MEMORY button for about 1 second while holding the MONITOR button on the front panel . · The print paper is automatically cut after sending by about 10cm. 4 Repeat 3 step. (Fingerprints and dust can be removed by feeding the print paper. CONNECTION CABLE CONNECTION Connect the components as follows. (example) Make sure to turn off each device when connecting. "C"(image in the camera) or "P"(image in the printer) is shown on the LCD. C/P C Print the image. When printing the first image (with "P" mark, an image memorized in the printer), press PRINT button. PRINT When printing the second image (with "C" mark, an image memorized in the camera), press MEM button first, then, press PRINT button. Printed image MEM PRINT Printed image 7. When printing only one image (not multiple picture), skip the step Refer to page 14 to get maximum quality of your pictures. 13 6. PICTURE QUALITY ADJUSTMENT ADJUSTING PICTURE QUALITY To adjust the image source first is the key to get maximum picture quality. Relation Distance for taking picture, Guide No. , F number Distance (m) 1 1. 5 2. 5 2 F IRIS F IRIS F IRIS F IRIS 12 8 -17 14 5. 6 13 11 -20 8 -17 16 16 -24 18 20 8 -17 11 -20 22 22 -28 16 -24 24 26 11 -20 Guide 28 30 No. 32 32 -30 22 -28 16 -24 34 36 38 40 16 -24 42 44 22 -28 46 48 32 -30 50 52 54 22 -28 56 2 CAMERA ADJUSTMENT Always adjust the camera setting first. Only after you are sure that the camera is providing the best picture quality and color balance, adjust the printer setting. Make sure to adjust the camera setting in the same condition which you actually take a picture. For Iris setting, see the table shown right. 2 ADJUSTING THE BRIGHTNESS OF IMAGE (IRIS) 1 Press SHOT button to take a picture. 2 Press IRIS button. IRIS adjustment mode is selected. SHOT MANUAL 0 3 Press UP or DOWN button to select MANUAL. If the image is too light, set the smaller value. MANUAL -20 Too dark Good Too light 5 Press SET button. 6 Press ZOOM button to finish the iris setting menu. 14 7 Press SHOT button to take a picture. Check the brightness of image. If the brightness is not improved, repeat the steps get the best setting. 2 to 6 to 2 ADJUSTING THE COLOR OF IMAGE (WHITE BALANCE) 1 Place a piece of white paper in front of the camera and display it to cover the LCD. Place a white paper at the actual position of a person who is taking a picture from the camera. NOTE Do not display the picture with non-white objects when adjusting white balance. [. . . ] 25mm (print size) x 1. 77 (ratio) = about 44mm (on LCD) So, you can mark a new circle on guide C. See page 12 for guide sheet. 22 10. of effective pixels Signal system Scanning system Scanning frequency Sync. system Video output Horizontal resolution S/N ratio Gain control White balance Color adjustment Electronic SHOT Closest distance Lens 1/4" CCD (total 470, 000 pixels) 752H x 582V (440, 000 pixels) PAL colour system 625 lines; 2:1 interlace 15. 625 kHz (H), 50 Hz (V) Internal PAL composite 430 TV lines (S-video output) More than 46dB AUTO / MANUAL AUTO / INDOOR/ FL LIGHT / OUTDOOR / LOCK / MANUAL R-GAIN / B-GAIN / R-HUE / B-HUE 1/50 1cm (widest angle) 1m (telephoto end) Electrically powered 14-power zoom lensF1. 4, f = 3. 9 - 54. 6mm Zoom speed 2 / 3 / 6 / 10 sec. Focus AUTO / LOCK / MANUAL Iris AUTO/MANUAL Operating 0°C to 40°C Safekeeping -20°C to +60°C DC12V 900mA (camera+LCD+video amp+PCB's) External dimensions Weight LCD Accesories 165mm(W) x 147mm(H) x 205mm(D) (excluding external connectors) Approx. [. . . ]