User manual MITSUBISHI PLFY

[. . . ] DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. When using the projector in Europe: COMPLIANCE NOTICE This Projector complies with the requirements of the EC Directive 89/336/EEC "EMC Directive" as amended by Directive 92/31/EEC and 93/68/EEC, and 73/23/EEC "Low Voltage Directive" as amended by Directive 93/68/ EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on smallscale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system. CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75. WARNING Use the attached RGB cable or RS-232C cable with this equipment so as to keep interference within the limits of an EN55022 Class B device. Please follow WARNING instructions. EN - 2 Contents ENGLISH Important safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · When a high-level audio signal, such as a DVD audio signal, is supplied to the AUDIO IN terminal, the output from the speaker may be distorted. AV mute The video and audio signals are temporarily muted when the MUTE button is pressed. To cancel muting, press the MUTE button again. ANAMORPHIC mode When playing DVD discs containing data of letterboxed image, press the 16:9 button. Important: · When a letterboxed image is kept displayd for a long time before displaying 4:3 image, the afterimages of the black bars may appear on the 4:3 image screen. Caution: · After using the projector, wait one minute for the air outlet fans to stop. · The lamp can't be lit again for one minute after turned off for safety purpose. If you want to turn on the projector again, wait until the indicator goes out, and then press the POWER button. · The air outlet fans rotate faster as the temperature around the projector rises. · When the temperature around the projector rises high, the sign "TEMPERATURE!!" blinks red on the screen. Important: · Do not display a still picture for a long time because the afterimages may persist on the screen. AUTO POSITION button When the image isn't projected in the right position with COMPUTER selected as the input source, follow the procedure below. Project a bright image such as the "Recycle Bin" window on the full screen. · If the image is still not in the right position, adjust the image position using the SIGNAL menu. When LOW is chosen, the lamp brightness is kept low and the projector operating noise is reduced, resulting in a longer lamp replacement interval. · When the lamp mode is switched, the projected image may flicker. For PLFY · When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about one minute after turn-on. For ES100U · You can't change the lamp mode for one minute after turning on the projector. Select MIRROR for rear projection with the tabletop-mounted projector. Select MIRROR INVERT for front projection with the ceiling-mounted projector. ON EN - 16 3 FEATURE opt. MENU POSITION . . . . . . . . . . . . . . . . . . . Use to select the position of the menu on the FEATURE (upper left) or 2. When AUTO is selected, the film mode will be AUTO CINEMA MODE automatically activated when a film source signal ?When OFF is selected, the film mode VIDEO SIGNAL will not be activated. When AUTO is selected, the appropriate video MENU ACCESS FUNCTION format is automatically selected depending on the AË English LANGUAGE input signal. If the image isn't displayed correctly, OK RESET ALL select the desired video format manually. [. . . ] · Relocate the projector to a cooler place. Steady red Steady red Blinking green The protection circuit is working or the lamp is in an abnormal condition. · Wait until the STATUS indicator goes out, then press the POWER button. Change with a new lamp if this problem recurs. Steady green Blinking green/red The lamp operation time exceeds the time elapsed until the lamp shutdown notice while the power is on. (See page 22. ) The lamp operation time exceeds the time elapsed until the lamp shutdown notice while the power is off. (See page 22. ) The lamp operation time exceeds the time elapsed until the lamp shutdown. [. . . ]