User manual MITSUBISHI S250

[. . . ] LCD Projector User Manual X250 S250 MODEL LVP-X250U / LVP-S250U EN ­ 1 APPENDIX ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class A device. [. . . ] · To prevent the damage of the LCD, the image and audio will be restored automatically to the normal mode, 10 minutes after setting the AV mute mode. · The audios from the audio output terminals and PC audio output terminal are not muted. Caution: · When you have finished using this equipment, wait 120 seconds for the exhaust fans to stop. Then turn off the main switch and unplug the power cable from the wall outlet, for safety purposes. · After the lamp is turned off, the lamp cannot be switched on again for 60 seconds as a precautionary measure. If you wish to turn on the projector again, wait until the indicator is off then press the POWER button. · The exhaust fan rotates faster when the temperature around the projector rises. · When the temperature around the projector becomes too high, the sign "TEMP!!" blinks red on the screen. If the temperature stays too high, the lamp will be shut off automatically . The projector automatically shuts off when the lamp is used up in about 2, 000. You must replace the lamp. 30 · The volume control bar will disappear about 10 seconds after releasing the volume buttons. · The volume buttons do not work when MENU selection bar or MENU is displayed. · The volume from the audio output terminals and PC audio output terminal are not changed. · If the high level of audio signal, for example DVD is supplied into PC AUDIO IN terminal, the speaker out may be distorted. EN ­ 14 Menu operation PICTURE USER COLOR TEMP. SHARPNESS TINT COLOR AUDIO BASS TREBLE PinP AUDIO IMAGE REVERSE KEYSTONE AUTO POWER ON AUTO POWER OFF TEST SIGNAL MENU POSITION MODE DISPLAY SPLASH SCREEN CINEMA MODE VIDEO SIGNAL LANGUAGE HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING COMPUTER INPUT USER CONTRAST R ± 30 CONTRAST B ± 30 BRIGHTNESS R ± 30 BRIGHTNESS B ± 30 (± 2 : When the source is selected to COMPUTER) (Displays only when the source is selected to VIDEO) (Displays only when the source is selected to VIDEO) 0-3 0-3 (Main) , (Sub) R R INSTALLATION (Invert) , (Mirror invert) R (Off) , R (Mirror) , ± 15° ON , OFF 0 (Off) , 5 , 10 , 15 , 20 , 25 , 30 , 35 , 40 , 45 , 50 , 55 , 60 min. ON , OFF (Upper left), (Lower right) ON , OFF ON , OFF (­ : When the source is selected to COMPUTER) AUTO , OFF AUTO , NTSC , PAL , SECAM , 4. 43NTSC , PAL-M , PAL-N , PAL-60 , English , Español , Deutsch , Français , Italiano , 0 - 999 * 0 - 999 * 0 - 32 0 - 9999 * RGB , YCBCR , YPBPR HOLD BEGIN HOLD END CLAMP POSITION CLAMP WIDTH ANAMORPHIC 1 - 99 1 - 99 0 - 63 0 - 63 ON , OFF OPTION SIGNAL * : Setting range is different according to the type of the signal. * * * * Basic operation Several settings can be adjusted using Menu. Press the { or } button to select AUTO POWER OFF. AUTO POWER ON AUTO POWER OFF TEST ON 0 min TEST SIGNAL ON OFF 1. Press the $ or % button to adjust auto power off time. AUTO POWER ON AUTO POWER OFF TEST PICTURE ON 30 min ON OFF 2. Press the $ or % button to select the OPTION menu. Opt TEST SIGNAL INSTALLATION 3. · If the menu operation is not working, press the RESET button on the terminal board using the suitable implement · If the COMPUTER or VIDEO button is pressed, the MENU selection bar or MENU will disappear. · The settings with 2 mark, you should press the ENTER button after selecting. INSTALLATION IMAGE REVERSE KEYSTONE AUTO POWER ON AUTO POWER OFF TEST R 0° ON 0 min TEST SIGNAL ON OFF EN ­ 15 ENGLISH CONTRAST BRIGHTNESS COLOR MATRIX ± 30 ± 30 1 2 3 USER OFF 1 (Standard) 2 (High) 3 (Low) 4 (User) ± 10 ± 10 ± 10 RED GREEN BLUE YELLOW CYAN MAGENTA ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 Menu operation (continued) 1 PICTURE CONTRAST . . . . . . . . (It can not be changed COLOR 0 on XGA resolution. ) TINT . . . . . . . . . . . . . . . . . . . . [. . . ] The image is blurred. · The projecting distance is beyond the focused area. · Lens is dirty. · Screen size exceeds screen size specifications. · · · · Brightness and contrast are not adjusted correctly. The projector is not at a right angle to the screen. Reduce screen size to within 40" to 300". Adjust brightness, contrast. Adjust the angle of the projector to make a right angle to the screen. [. . . ]