User manual MITSUBISHI S50

[. . . ] LCD Projector User Manual S50 MODEL LVP-S50U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class A device. [. . . ] · Set screen to the brightest display as possible (e. g. , full-screen display of the "Trash" window) before deploying the automatic adjustment function. · If the screen saver is running, turn off the screen saver before using the automatic adjustment button. · The output sound is selected by changing the setting of AUDIO MODE in the FEATURE menu. The volume from the speaker Press the volume + or ­ button to change the volume from the speaker. · The volume control bar will disappear about 4 seconds after releasing the volume buttons. · The volume buttons do not work when MENU selection bar or MENU is displayed. AV mute Image and audio are temporarily erased with pressing the MUTE button. To restore the image and audio to the normal mode, press the MUTE button again. · To prevent the damage of the LCD, the image and audio will be restored automatically to the normal mode, 10 minutes after setting the AV mute mode. · The audios from the audio output terminals and PC audio output terminal are not muted. Caution: · When you have finished using this equipment, wait 120 seconds for the exhaust fans to stop. Then turn off the main switch and unplug the power cable from the wall outlet, for safety purposes. · After the lamp is turned off, the lamp cannot be switched on again for 60 seconds as a precautionary measure. If you wish to turn on the projector again, wait until the indicator is off then press the POWER button. · The exhaust fan rotates faster when the temperature around the projector rises. · When the temperature around the projector becomes too high, the sign "TEMP!!" blinks red on the screen. If the temperature stays too high, the lamp will be shut off automatically . The projector automatically shuts off when the lamp is used up in about 2000 hours. You must replace the lamp. 30 EN ­ 14 Menu operation IMAGE USER COLOR TEMP. CONTRAST R CONTRAST B BRIGHTNESS R BRIGHTNESS B ± 30 ± 30 ± 30 ± 30 SHARPNESS TINT COLOR INSTALLATION IMAGE REVERSE AUTO POWER ON AUTO POWER OFF MENU POSITION EXPAND MODE AUDIO MODE VIDEO SIGNAL ANAMORPHIC LANGUAGE MEMORY CALL HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING COMPUTER INPUT HOLD (Displays only when the source is selected to VIDEO) (Displays only when the source is selected to VIDEO) OFF, MIRROR, INVERT, MIRROR INVERT ON, OFF OFF, 5, 10, 15, 30, 60 min 1=Upper left, 2=Lower right 1-2 (AUTO : When the source is selected to COMPUTER) 1-3 AUTO, NTSC, PAL, SECAM, 4. 43NTSC, PAL-M, PAL-N, PAL-60 ON, OFF , English, Español, Deutsch, Français, Italiano, AUTO, USER1, USER2 0 - 999 * 0 - 999 * 0 - 39 0 - 9999 * RGB, YCBCR / YPBPR AUTO ON OFF FEATURES SIGNAL * : Setting range is different according to the type of the signal. BEGIN END -1 - -99 1 - 99 0 - +63 * 0 - +63 * 0 - 9999 * 0 - 9999 * AUTO, 0 - 7 AUTO, ON, OFF 0 - 299 0 - 299 USER MEMORIZE DELETE DEFAULT USER1, USER2 USER1, USER2 CLAMP POSITION CLAMP WIDTH HORIZ. SYNC SHUTTER (U) SHUTTER (L) Basic operation Several settings can be adjusted using Menu. Press the { or } button to select AUTO POWER OFF. IMAGE REVERSE AUTO POWER ON AUTO POWER OFF OFF OFF OFF 5. [. . . ] (In this case, the TEMP indicator does not light up. ) The image is · The projector is not at a right angle to the screen. The image is blurred. · The projecting distance is beyond the focused area. · Lens is dirty. · Screen size exceeds screen size specifications. · · · · Brightness and contrast are not adjusted correctly. The projector is not at a right angle to the screen. Reduce screen size to within 40" to 300". Adjust brightness, contrast. [. . . ]