User manual MITSUBISHI SEZ-KD09

[. . . ] Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Terminal Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wireless Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Range for the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Product warranty does not cover damage caused by improper installation. Failure to follow these recommendations could result in voiding your warranty. Use M6 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them securely. MITSUBISHI ELECTRIC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America. · Install the monitor with metal brackets for wall or ceiling installation (commercially available) on your own responsibility. For detailed procedures of installation, refer to the instructions of the metal brackets. · To lessen the probability of injury and damage resulting from fall of the monitor in case of earthquake or other disaster, be sure to consult the bracket manufacturer for installation location. · To lessen the risk of falling of the monitor, thread commercially available rope (having a load capacity at least 1960N (200kgf)) through the handles at the right and left of the monitor and secure the rope to the wall mount brackets or ceiling mount brackets. · Do not sleep where the monitor may topple over or fall in case of an earthquake or other disaster. 331. 5 Rope, etc. commercially available Clamper Screw Caution: · The effectiveness of preventing from falling substantially depends on the strength of brackets and base to which prevention device from falling is attached. When you cannot ensure sufficient strength, provide adequate reinforcement. The AUDIO OUT jack outputs sound from the selected Audio input. VCR or CD player Monitor To composite Output In case of VCR RCA RCA BNC To audio right output To audio left output To audio right input RCA External speaker To audio left input RCA BNC LCD monitor (second monitor) External speaker English-18 Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on or red in off mode. The monitor can be powered on or off using the following three options: 1. Pressing the Main Power Switch. NOTE: When the Main Power Switch is used to power off the LCD monitor, the remote control and the power button will not activate the on mode and both green and red power indicator turn off. Be sure to turn the Main Power Switch to the on mode before using these two options. Pressing the power button. NOTE: Before pressing the power button, be sure to turn on the Main Power button on the LCD monitor. Power Button 3. Using the remote control. NOTE: Before operating the remote control, be sure to turn on the Main Power Switch on the LCD monitor. English-19 English Power Indicator Status Power ON Power OFF Power Standby when "SCHEDULE" is enable Power Standby Diagnosis (Detecting failure) Green Red Red On Green Blinking Red, Green Red Blinking * See troubleshooting on page 35 NORMAL: Display by the inputed signal aspect ratio by PC signal, or display in 4:3 aspect ratio at DVD/HD or VIDEO signal. (Some round image will be cut by expansion. ) CUSTOM (ZOOM): Image can be expanded beyond the active display area. ZOOM Using Power Management The LCD monitor follows the VESA approved DPM Power Management function. The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or the mouse has not been used for a fixed period. The power management feature on your new display has been set to the "ON" mode. This allows your display to enter a Power Saving Mode when no signal is applied. [. . . ] > When Host computer ask Power status of monitor, the status of monitor is powered-on. Detail of command Command from computer Command from Monitor Ask about the power status of monitor 30 30 76 50 0D '0''0''v''P'[enter] 30 30 76 50 31 0D '0''0''v''P''1'[enter] Monitor is powered-on. Structure of the Read-command Function vP vP vI vI vI vI vI vI vI vM vM tc1 tc2 ASCII Data (Receive) 1 0 r1 r2 r3 r4 v1 v2 v3 p1 p2 (ex. ) +25 (ex. ) +31 Function 76 50 76 50 76 49 76 49 76 49 76 49 76 49 76 49 76 49 76 4D 76 4D 74 63 31 74 63 32 HEX Data (Receive) 31 30 72 31 72 32 72 33 72 34 76 31 76 32 76 33 70 31 70 32 2B 20 32 35 2B 20 33 31 POWER Input Picture mode Temperature of internal monitor ON OFF(stand by) RGB-1(HDMI1) RGB-2(HDMI2) RGB-3(D-SUB) RGB-4(BNC) Video DVD/HD S-VIDEO HIGHBRIGHT STANDARD resolution Around 1 °C Main board Around resolution Power PCB 1 °C English-33 English Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The monitor's small footprint and low weight allow it to be moved or transported easily from one location to another. Color Control Systems: Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards. sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays and other peripherals. [. . . ]