User manual MITSUBISHI SL1U

[. . . ] LCD Projector User Manual SL1 MODEL SL1U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class B device. [. . . ] COMPUTER COLOR MATRIX · When sRGB is ON, the image will become darker. STANDARD · When COLOR TEMP is set to other than STANDARD COLOR 0 while sRGB is ON, colors won't be reproduced as per TINT 0 the standard value of sRGB. SHARPNESS 0 · Though sRGB can be ON while a signal is input from VIDEO-IN or S-VIDEO IN, reproduced colors won't be in accordance with the sRGB standard value. (Available only when VIDEO is selected as the source. ) TINT . . . . . . . . . . . . . . . . . . . . The color balance of the image shifts green as the number increases and shifts to purple as the number decreases. (Available only when VIDEO is selected as the source. ) · When the TV50 (PAL, SECAM) signal is inputted, TINT can't be adjusted. XGA60 automatically adjusts the brightness and contrast of the image depending on the degree of the light in the room. When using INSTALLATION IRIS OFF this projector in a room where the light and shade varies slightly, select 1. When using this projector in a normally KEYSTONE 0° AUTO POWER lighted room, select 2. When using this projector in a room OFF ON where the light and shade varies greatly, select 3. When you AUTO POWER OFF OFF select OFF, IRIS won't operate. SPLASH SCREEN ON · When the sensitivity is adjusted in a large amount, the BACK COLOR BLUE image may be displayed solid white. Adjust the LAMP MODE STANDARD sensitivity depending on the operating environment OFF IMAGE REVERSE and imges to be displayed. Select ON to boot up the projector automatically by turning on an externally connected power switch such as a breaker even when the main power switch of the projector is off. · The projector will be in the stand-by mode when the lamp is off. Set the time elapsed before the projector enters into the stand-by mode when there is no signal inputted from the selected source. Use to select the color of the background, blue or black, which will be displayed when there is no signal inputted from the selected source. When LOW is selected, the image will become darker, though the power will be saved, operating sound will be reduced. · The brightness of the lamp will be STANDARD for 3 minutes regardless of the setting of the LAMP MODE when the lamp turns on. Select MIRROR, INVERT in rear projection with the projector hanging from the ceiling. ON 3 FEATURE MENU POSITION . . . . . . . Use to select the position of the menu on the screen, (upper left) or (lower right). Select COMPUTER to output the sound which is inputted to the audio input terminal when COMPUTER is selected as the source. Select VIDEO to output the sound which is inputted to the audio input terminal when VIDEO is selected as the source. [. . . ] When having a control sequence by RS232C, reject other codes from personal computer side. · * : The sending time of return command may delay depending on the condition (during changing the input signal, etc. ). [Example] Turn the power ON (' 'is for ASCII code) Sending commands from the PC etc. 30 30 21 0D '0' '0' '!' ' ' 30 30 21 0D '0' '0' '!' ' ' Command received (Command echo back) Status code from projector Command for POWER ON Meaning 4) Operation commands The operation commands execute the basic operation setting of this projector. It may not operate when changing the signal. Operation POWER ON POWER OFF INPUT COMPUTER INPUT VIDEO INPUT S-VIDEO ASCII ! [. . . ]