User manual MITSUBISHI VS-50XLF50U

[. . . ] Attachments and equipment Never add any attachments and/or equipment without the approval of the manufacturer as such additions may result in the risk of fire, electric shock or other personal injury. Water and moisture Do not use this product near water or in contact with water. Accessories Do not place this product on an unstable cart, stand, tripod, bracket or table. Use only with a cart, stand, tripod bracket, or table recommended by the manufacturer or sold with the product. [. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled "Digital Apparatus", ICES-003 of the Department of Communications. Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this equipment. COMPLIANCE NOTICE OF INDUSTRY CANADA This Class A digital apparatus complies with Canadian ICES-003. COMPLIANCE NOTICE OF EC DIRECTIVE This data display complies with requirements of 89/336/EEC, 2006/95/EC and 93/68/EEC. The requirements of susceptibility have chosen at a level, that makes interference free operation possible in living areas, office areas and light industry, related to indoor and outdoor operation. All places of operation are related to the public low voltage power supply. This device could cause interferences in residential areas; in the case of interferences it can be demand from the user to provide appropriate solutions and pay for it. Warning: This is class A information technology equipment. When used in a household environment, this product may cause radio interface. In such a case, the user may be required to take suitable countermeasures. EN-4 Model Screen size RGB input signal supported Analog RGB Terminal Signal input Digital RGB Terminal Signal input Control Power consumption Power supply Width External dimensions Height (excluding protrusions) Depth Operating temperature and humidity Weight Accessories VS-50XL50U VS-50XLW50U VS-50XLF50U VS-50XLWF50U VS-67XL50U VS-67XLW50U VS-67XLF50U VS-67XLWF50U 50 inches 50 inches 67 inches 50 inches 50 inches 67 inches 67 inches 67 inches (1015 x 761 mm) (1015 x 761 mm) (1015 x 761 mm) (1015 x 761 mm) (1359 x 1019 mm) (1359 x 1019 mm) (1359 x 1019 mm) (1359 x 1019 mm) Resolution: VGA ­ SXGA+, Horizontal: 31. 5 to 78 kHz, Vertical: 49 to 85 Hz, Pixel clock rate: 25 to 122 MHz BNC x 5 (RGBHV) RGB signal level: 0. 7 V (p-p) 75, Sync: TTL level (positive/negative) Sync On Green DVI-D TMDS RS-232C: D-Sub 9-pin Mitsubishi original control link: D-Sub 9-pin x 2 (input and output) 195 W AC 100 V ­ 240 V 50/60 Hz 2. 5 A 1017 mm (40 inch) 1017 mm (40 inch) 1016 mm (40 inch) 1361 mm (53. 6 inch) 1362 mm (53. 6 inch) 982. 5 mm (38. 7 inch) 982. 5 mm (38. 7 inch) 982 mm (38. 7 inch) 1180. 3 mm (46. 5 inch) 1282. 3 mm (50. 5 inch) 595 mm (23. 4 inch) 660 mm (26. 0 inch) 535 mm (21. 1 inch) 778 mm (30. 6 inch) 848 mm (33. 4 inch) 10°C ­ 30°C (50°F ­ 86°F) 10°C ­ 30°C (50°F ­ 86°F) 10°C ­ 35°C (50°F ­ 95°F) 10°C ­ 35°C (50°F ­ 95°F) 10°C ­ 30°C (50°F ­ 86°F) 20 % ­ 70 % 20 % ­ 80 % 20 % ­ 70 % 20 % ­ 80 % 20 % ­ 70 % 60 kg (132 lbs) 75 kg (165 lbs) 90 kg (198 lbs) 92 kg (203 lbs) 62 kg (137 lbs) 93 kg (205 lbs) 69 kg (152 lbs) 95 kg (209 lbs) User's manual Joint parts (8 pcs. each of hexagon socket head cap screws for M6, flat washers, and spring washers) Control cable Joint hole seal Plastic tie (6 pcs. Do not attempt to replace the lamp and carry out the adjustments by yourself. Disposal of the lamp or the product with the lamp may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or Electronic Industries Alliance : www. eiae. org. (For US only) · VS-50XL50U, VS-67XL50U This product is equipped with a lamp to display images generated the DLPTM chip. (Blue light blinks on the screen when the lamp doesn't illuminate any more. ) You may purchase a new lamp from your authorized MITSUBISHI dealer. Part number for the lamp used in the VS-50XL50U and VS-67XL50U is S-XL50LA This product uses a lamp that contains mercury. Disposal of the lamp or the product with the lamp may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or Electronic Industries Alliance : www. eiae. org. (For US only) Warning: · Be sure to turn off the main power switch and unplug the power cord from the wall outlet before replacing the lamp. Lamp replacement without turning off the main power may result in electric shock. Using the product with any foreign object inside may result in electric shock or fire. [. . . ] Contact your MITSUBISHI dealer. The cover of the lamp changer is open. Contact your MITSUBISHI dealer. STATUS Light on for 5 seconds, off for 1 second STAND BY STATUS The power circuit has failed. Contact your MITSUBISHI dealer. STAND BY STATUS The power circuit, cooling fan, or image processing circuit has failed. Contact your MITSUBISHI dealer. STAND BY STATUS STAND BY Light on for 1 second, off for 5 seconds STATUS STAND BY Displays number 1, 2, 3, 4 or 5. STATUS The image processing circuit has failed. [. . . ]