User manual MITSUBISHI WD-52825

[. . . ] Projection Television Models WD-52825, WD-62825 TM Owner's Guide TV Information: Use this space to record the model and serial numbers of your television. Model number Serial number TM visit our website at www. mitsubishi-tv. com CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated "dangerous voltage" within the product's enclosure that may be sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This TV is very heavy!To prevent damage to your TV, your TV should not be jarred or moved while it is turned on. [. . . ] For example, if the IEEE 1394 device you have added is a Mitsubishi DVCR, and you have selected an analog connection as a second connection, then you will select Mitsubishi for the manufacturer. If the manufacturer is not listed, select "Other" and use the Learn screens. Be sure to place an IR Emitter in front of the remote control sensor, just as you have done for other NetCommand® devices. It is necessary to use the IR Emitter only when the DVCR is being used as an S-VHS or VHS VCR. When the DVCR is playing or recording digital signals in D-VHS, the TV will control the VCR through the IEEE 1394 cable. Figure 5. Connection screen Finish Screen To finalize your selections and complete the NetCommand setup, select Finish from the Finish screen. Figure 6 Figure 4. Finish screen 52 Device Selection Menu When you press DEVICE on the TV's remote control, the Device Selection menu (Figure 7) displays. If NetCommand® has not been setup, the Device Selection menu allows you to select an input for viewing. If NetCommand is setup, the Device Selection menu allows you to select the device for viewing, select audio from the TV speakers or A/V receiver, power compatible devices On or Off, and verify the destination of signals. On the Device Selection menu, the device or input currently displayed appears as a gold-colored icon. Video Section Connection Section Audio Section Device Section Audio Section When a NetCommand pre-memorized or learned IR controlled A/V receiver has been connected to the TV and added to NetCommand Setup, an AVR icon will appear in the audio section. Then press ADJUST , , or to select the TV speakers icon or the A/V receiver icon. Press DEVICE to return the navigation to the Device Section. Figure 7. Device Selection Menu with NetCommand PIP Device Selection Menu Figure 8 Devices that have separate On and Off remote control buttons will power On automatically when you select the device and will power Off when you turn off the TV. For devices that do not power On or Off automatically, display the Device Selection menu, press ADJUST or to highlight the device icon and press POWER on the remote control. For the A/V receiver, press AUDIO to move the navigation to the Audio Section. If you press POWER on the remote control when the Device Selection menu is not displayed, the TV will turn Off. Device Section To select another device or input, press ADJUST , , or on the TV's remote to move the highlight. If NetCommand is set up, the inputs on compatible A/V receivers are automatically changed at the same time. Video Section The destination of the device ighlighted in the Device Section is displayed here as a TV icon. Connection Section The Connection Section shows the other devices currently connected to the device highlighted in the Device Section. For example, if the Digital VCR (D-VCR) is currently recording, when you move the highlight to the Ant-1 icon, the D-VCR icon will appear in the Connection Section. This icon will disappear when you move the highlight to another icon, press CANCEL to stop recording. Power On/Off Devices The PIP Selection menu displays when you press the PIP DEVICE button on the remote control. [. . . ] As in other display technology, sometimes a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MDEA warrants only that the percentage of properly functioning pixels will be not less than 99. 99% of all pixels. BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and correct customer control adjustment. Contact your nearest authorized MITSUBISHI service center whose name and address can be obtained from your MITSUBISHI dealer, by writing at the address provided below, calling MDEA at the 800-332-2119, or use the support feature of our website at www. mitsubishi-tv. com. [. . . ]