User manual MITSUBISHI WD570U

[. . . ] DLPTM PROJECTOR MODEL XD550U XD560U WD570U User Manual XD550U XD560U WD570U This User Manual is important to you. Please read it before using your projector. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power supply cord, it may cause interference with radio and television reception. Use the attached RGB cable and the shielded LAN cable with this equipment so as to keep interference within the limits of an FCC Class B device. [. . . ] Align the left edge of the image with the left side of the screen by adjusting H. Position. Then, align the right edge of the image with the right side of the screen by adjusting Tracking. Align the upper edge of the image with the upper side of the screen by adjusting V. Position. How to adjust the image supplied from the computer using the menu: Perform the following procedures when the following conditions occur. To select On , press the ENTER button, and Adjust Begin or End to minimize the flagging. · Do not change the settings of the Signal menu for ordinary use. LPF (Progressive filter) You can select to enable or disable the LPF. Vertical or horizontal streaks may appear in the projected image, depending on the type of the DVD player, game console or computer in use. Projected images appear slightly faint. EN-32 Network settings You can set the network of the projector using the menu. Network Config Projector Name Network Certification Network Password IP Config Wireless Setting AMX Device Discovery Network Initialization Network Restart Adjust Select SET On OK OK OK Off OK OK MENU Exit Enabling or disabling the network certification You can select whether or not to certify the network communication using the network password. Press the or button to select Network Certification. Network Certification On 3. · Certification dialog appears. Setting Projector Name (See page 21 for menu setting. ) 1. Press the or button to select Projector Name. Projector Name SET 3. · It may take some time to reflect the setting. Network Password settings (See page 21 for menu setting. ) 1. Press the or button to select Network Password. Network Password OK 5. Press the , , , and buttons to move the key cursor to select the characters or marks to enter, and press the ENTER button. · Projector Name can be set using up to 15 characters including alphabets (capital/small), numeric characters, or marks. key: Shifting the position of enter cursor to the left for each character. key: Shifting the position of enter cursor to the right for each character. DEL key: Deleting the character in the position of enter cursor for each character. · The display returns to the Network Config menu after selecting OK or CANCEL. · CURRENT NETWORK PASSWORD screen appears. Press the , , , and buttons to move the key cursor to select the characters or marks to enter, and press the ENTER button. · Password can be set using up to 32 characters including alphabets (capital/small) or numeric characters. key: Shifting the position of enter cursor to the left for each character. key: Shifting the position of enter cursor to the right for each character. [. . . ] If these problem persist, turn the projector off and consult your dealer. STATUS indicator POWER indicator Normal condition POWER Steady red STATUS Stand-by Off CONDITION NOTE Lamp stand-by (about 1 minute) Steady green Blinking green The POWER button cannot be used to switch between on and off. The power is on. (Normal condition) Steady green Steady green Abnormal condition POWER Steady green or Blinking orange Steady red STATUS CONDITION Abnormal temperature · The ventilation grilles is clogged with dust or dirt. The protection circuit is working or the lamp is in an abnormal condition. Relocate the projector to a cooler place. · · Steady red Blinking green Wait until the STATUS indicator goes out, then press the POWER button. [. . . ]