User manual MITSUBISHI WD8200U

[. . . ] DLPTM PROJECTOR MODEL WD8200U WD8200LU User Manual WD8200 This User Manual is important to you. Please read it before using your projector. U CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: CAUTION: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. [. . . ] (See page 52. ) EN-40 Menu operation (continued) INFORMATION menu opt. 1 2 INFORMATION LAMP 1 TIME (LOW) LAMP 2 TIME (LOW) NEXT LAMP RELAY FILTER TIME SERIAL NUMBER INPUT RESOLUTION VERTICAL FREQUENCY HORIZONTAL FREQUENCY RGB H V ****H ****H *D **H *****H / ****TIMES ********. . . COMPUTER1 1024 x 768 60. 00 Hz 48. 36 kHz 5WIRE SYNC. TYPE ITEM LAMP 1 TIME (LOW) LAMP 2 TIME (LOW) NEXT LAMP RELAY FILTER TIME SERIAL NUMBER INPUT RESOLUTION VERTICAL FREQUENCY HORIZONTAL FREQUENCY SYNC. TYPE DESCRIPTION This item shows the lamp operation time calculated based on that the LAMP MODE of LAMP 1 is LOW. · WhentheLAMPMODEisSTANDARD, thisitemshowsalongerlampoperatingtimethan the actual time. · Whenthelampoperatingtimeis0to10hours, "0H"isdisplayed. Thelampoperatingtime exceeding 10 hours is indicated by the actual hours. · Whenthelampoperatingtimereaches3000hours, thebarturnstoyellow. Whenit reaches 3800 hours, the bar turns to red. Yellow: On, Red: End of lamp life or error such as illumination failure, Black: Off This item shows the lamp operation time calculated based on that the LAMP MODE of LAMP 2 is LOW. · WhentheLAMPMODEisSTANDARD, thisitemshowsalongerlampoperatingtimethan the actual time. · Whenthelampoperatingtimeis0to10hours, "0H"isdisplayed. Thelampoperatingtime exceeding 10 hours is indicated by the actual hours. · Whenthelampoperatingtimereaches3000hours, thebarturnstoyellow. Whenit reaches 3800 hours, the bar turns to red. Yellow: On, Red: End of lamp life or error such as illumination failure, Black: Off The next lamp relay time is displayed. Indicates the name of the terminal to which the currently projected video signal is being input. Indicates the vertical frequency of the currently projected video signal. Indicates the horizontal frequency of the currently projected video signal. Indicates the type of the sync signal for the currently projected video signal. · NEXTLAMPRELAYisn'tdisplayedwhenLAMPRELAYisOFForLAMPSELECTisLAMP1orLAMP2intheINSTALLATION 1 menu. EN-41 Adjusting projected images To adjust the brightness (CONTRAST and BRIGHTNESS): You can make adjustments for the brightness of the projected image using the menu. Every time the button is pressed, the image becomes brighter and more defined. Every time the button is pressed, the image becomes darker and less defined. BRIGHTNESS Every time the button is pressed, the image becomes brighter. Every time the button is pressed, the image becomes darker. To adjust the color (COLOR and TINT): You can adjust the color of the projected image using the menu. · COLORorTINTisunavailablewhenCOMPUTER1, COMPUTER2, DVIorHDMIisselectedastheinputsource. Every time the button is pressed, the image appears more reddish. To sharpen or soften the projected image (SHARPNESS): You can adjust the sharpness of the projected image using the menu. Press the MENU button. To adjust the tone of white (COLOR TEMP. ): You can select a preset color temperature (white tone) using the menu. [. . . ] It may not display images of higher resolutions than 1280 x 800 correctly. · Images with SYNC on G (Green) signal may be tinged with green. · If the resolution and frequency of your computer aren't shown on the table, find the compatible resolution and frequency by changing the resolution of your computer. When these signals are supplied to the VIDEO IN or S-VIDEO IN terminal, the signal mode is indicated as TV60 or TV50. [. . . ]