User manual MITSUBISHI X30U

[. . . ] Data Projector User Manual X30 MODEL LVP-X30U ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IMPORTANT Digital Light Processing, DLP, Digital Micromirror Device and DMD are all trademarks of Texas Instruments. [. . . ] 1 Use right hands to lift the front of the main unit to approximately the desired adjustment angle. 4 Rotate the contact surfaces of the rear adjuster either clockwise or counterclockwise to accurately adjust the level. 7 4 Up 1 2 Down Adjust the image size to match the distance to the screen. Next, use the focus ring to adjust the focus. Focus ring 3 Up 8 Down 6 When distortion of the projected image cannot be corrected with the adjusters, press the KEYSTONE +/­ buttons of the remote control to fine adjust (see page 18). Using KEYSTONE to adjust projected image distortion. ZOOM KEYSTONE VOLUME Change the unit setting to suit the method and source selected in step 4. · Select the "PROJECTION" appropriate for the type of projector installation. (See page 29) If the image is projected reversed, vertically, or horizontally, reset "PROJECTION". · In the case of video or S-video, select the color system as necessary. (See page 26) Normally, it is not necessary to change the factory settings. (See page 27) · In the case of RGB input, adjust the video of the connected PC. Note Maximum correction is 14 degrees (including optical correction). This projector automatically identifies the input signal and selects the most appropriate resolution. However, manually adjust the "PICTURE ADJ" and "FINE PICTURE" (see page 24) when there is flicker, noise, color offset, etc. , and manually adjust the vertical and horizontal position (see page 24) when the image is not centered. You can also choose to project the image at the original size of the incoming signal resolution. (Normally, the resolution is automatically sensed and the display is enlarged or reduced. ) E ­ 15 (Continued on the next page. ) ENGLISH Adjuster Adjustment The top and bottom of the projected image is corrected, as shown below. If a menu is being displayed, distortion of the menu will not be corrected. Using the unit (continued) Using the Remote Control (Input Selection) 9 10 Adjust the picture elements (see page 22), then select the picture type according to the video content (see page 26). MOUSE MENU POWER Start using the unit. The following functions are available while using the unit: · Adjusting the volume of the unit's speaker (see pages 18 and 28), · Turning off the image and muting the sound temporarily (see page 18), · Freezing a moving picture (see page 18), · Enlarging the picture (see page 19) Note · When there is no signal input for a period of 5 min. or more, the power is automatically turned off and standby status is activated. (see page 29) VIDEO button VIDEO CANCEL RGB RGB button Operating from the main unit Inputs can be selected not only by operating the remote control but also by using the main unit SOURCE button. POWER STATUS POWER SOURCE AUTO SOURCE button 1 Press the VIDEO button. The video signal (VIDEO, S-VIDEO) connected to the input jack of this device will be detected and projected automatically. If a video signal is not detected, the message NO SIGNAL will be displayed. After using the unit VIDEO 1 Press the POWER button of the remote control or the POWER button of the main unit for a few seconds. The power will turn off and the POWER indicator will blink amber for 1 min. , then the standby status will be activated. (The exhaust fan will continue to run for a while for cooling purposes. ) Do not unplug the power cord while the indicator is blinking. MOUSE MENU VIDEO CANCEL RGB POWER POWER ST 2 Press the RGB button. The analog RGB signal connected to the input connector of this device will be detected and projected automatically. (Component video will be detected if the RGB/ YCbCr connector is set (page 27) to YCbCr. ) If a video signal is not detected, the message NO SIGNAL will be displayed. RGB POWER Note Blinks amber (1 min. ) Lights amber Note · All video signals input to this device will be detected if Auto Source (page 29) is set. 3 Press the SOURCE button. The video signal (RGB or YCbCr, VIDEO, SVIDEO) connected to the input jack of this device will automatically be detected and projected. If a video signal is not detected, the message NO SIGNAL will be displayed. SOURCE · The POWER switches of the remote control and main unit will not operate until the blinking stops. · The exhaust fan will continue to run even in standby status. 2 Disconnect the power cord. The POWER indicator will turn off. RGB/YCbCr S-VIDEO VIDEO Note · When Auto Source (see page 29) is set to ON, all signals input to this projector will be sensed. E ­ 16 Using the Mouse Remote Control as the PC ENGLISH The remote control of this projector can be used as the PC mouse (wireless mouse function) by connecting the MOUSE connector of this projector and the PC. Remote control mouse functions · The cursor key on the remote control operates the computer mouse functions. · If a computer running Windows is connected, the ENTER button on the remote control operates as the computer mouse left click button and the CANCEL button as the computer mouse right click button. · If a Macintosh computer is connected, the ENTER and CANCEL buttons operate in the same way MOUSE button as the computer mouse click button. MOUSE MENU VIDEO CANCEL POWER RGB Connecting a PC and the MOUSE connector of this projector Before connecting a PC · Before connecting, turn off the PC power. · When connection is completed, turn on the power of this projector and then start the PC. USB Port Connection Connect the supplied USB mouse cable directly to the USB port (universal serial bus) of the personal computer, as shown in the diagram. [. . . ] Replace it correctly. · The temperature protector has been triggered. If the temperature within the unit is high, check the cooling fan ventilation slots and the ventilation slots on the bottom of the unit. If you try to turn on the unit immediately after turning off, sometimes the power does not come on. If this happens, wait at least one minute, then turn on the unit again. [. . . ]