User manual MITSUBISHI XD200

[. . . ] DATA Projector User Manual X D200 SD200 MODEL XD200U / SD200U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached PS/2 adapter cable, USB adapter cable and RGB cable with this equipment so as to keep interference within the limit of a FCC Class B device. [. . . ] Press the $ or % button to adjust auto power off time. AUTO POWER ON AUTO POWER OFF OFF 30min IMAGE 2. Press the $ or % button to select the INSTALLATION menu. opt. TV60 INSTALLATION 6. · If the menu operation is not working, turn off the main power, wait about 10 minutes, and turn on the main power again. · The settings with mark, you should press the ENTER button after selecting. 3. Press the ENTER button (or } button). opt. TV60 INSTALLATION AUTO POWER ON AUTO POWER OFF OFF OFF EN ­ 15 ENGLISH CONTRAST BRIGHTNESS sRGB COLOR MATRIX *1 ± 20 ± 20 ON, OFF VIDEO COMPUTER USER OFF STANDARD LOW HIGH USER ± 10 ± 10 ±5 RED YELLOW GREEN CYAN BLUE MAGENTA SATURATION CONTRAST R CONTRAST B BRIGHTNESS R BRIGHTNESS B ± 30 ± 30 ± 30 ± 30 ± 30 ± 30 ± 10 ± 15 ± 15 ± 15 ± 15 Menu operation (continued) 1 IMAGE opt. Select ON to display an image emphasizing on the color 0 BRIGHTNESS reproducibility. · When sRGB is ON, COLOR MATRIX can't be adsRGB OFF justed. OFF COLOR MATRIX · When sRGB is ON, the image will become darker. is set to other than STANCOLOR TEMP STANDARD DARD while sRGB is ON, colors won't be reproduced TINT 0 as per the standard value of sRGB. · Though sRGB can be ON while a signal is input from 0 COLOR VIDEO-IN or S-VIDEO IN, reproduced colors won't SHARPNESS 0 be in accordance with the sRGB standard value. The color balance of the image shifts green as the number increases and shifts to purple as the number decreases. (Available only when VIDEO is selected as the source. ) · TINT cannot be adjusted when a TV50 (PAL or SECAM) signal is being displayed. (Available only when VIDEO is selected as the source. ) SHARPNESS . . . . . . turning on an externally connected power switch such as TV60 a breaker even when the main power switch of the INSTALLATION projector is off. Use this setting when the projector is AUTO POWER hanging from the ceiling. OFF ON · The projector will be in the stand-by mode when the AUTO POWER OFF OFF lamp is off. Set the time elapsed before the projector enters into the BACK COLOR BLUE stand-by mode when there is no signal present at the IMAGE selected source. Select the color of the background to blue or black, this will be displayed when there is no signal present at the selected source. Select MIRROR, INVERT in rear projection with the projector hanging from the ceiling. ON 3 FEATURE MENU POSITION . . . . . Use to select the position of the menu on the screen, UPPER LEFT or LOWER RIGHT. · Though square-shaped noise may appear in the projected image when 1 is selected, this is not failure. · A playback signal on a deteriorated videotape or a poor-quality signal may not be projected properly. [. . . ] (The commands must be sent at least 400ms apart. ) (2) The projector will send a return command 400ms* after it has received an end code. If the command is not received correctly, the projector will not send the return command. (3) The personal computer checks the command and confirms if the command which has been sent has been executed or not. When having a control sequence by RS232C, reject other codes from personal computer side. [. . . ]