User manual MITSUBISHI XD206

[. . . ] N DATA PROJECTOR MODEL XD206U User Manual This User Manual is important to you. Please read it before using your projector. ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of suffcient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. Use the attached RGB cable with this equipment so as to keep interference within the limit of an FCC Class B device. [. . . ] BRIGHTNESS 0 COLOR TEMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to adjust the color temperature. WHITE ENHANCE 10 COLOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to adjust the color intensity of the image. TINT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to adjust the color balance of the image. The color COLOR 0 balance shifts to green as the value increases and shifts TINT 0 to purple as the value decreases. (Available only when SHARPNESS 0 VIDEO or S-VIDEO is chosen as the source. ) STANDARD GAMMA MODE · When the TV50 (PAL, SECAM) signal is input, TINT can't be adjusted. SHARPNESS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to adjust the image sharpness. (Not available with certain signals. ) GAMMA MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . When AUTO is selected, the appropriate gamma mode is automatically selected depending on the input signal. Select THEATER for film sources. 2 INSTALLATION AUTO POWER ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . When ON is chosen, the lamp is automatically lit when opt. INSTALLATION · The projector is in the stand-by mode when the lamp OFF AUTO POWER ON is off. OFF AUTO POWER OFF AUTO POWER OFF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to set the time elapsed before the projector enters SPLASH SCREEN ON the stand-by mode when there is no signal input from the BACK COLOR BLUE source. STANDARD LAMP MODE SPLASH SCREEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Choose ON to display the splash screen when the power IMAGE REVERSE OFF is turned on. LAMP HOURS 0 BACK COLOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to select the background from among BLUE and BLACK, which will be displayed when there is no signal input from the source. LAMP MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to change the brightness of the lamp. When LOW is chosen, the lamp brightness is kept low and the projector operating noise is reduced, resulting in a longer lamp replacement interval. · When the lamp mode is switched, the projected image may flicker. · When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about one minute after turn on. IMAGE REVERSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to reverse the projected image. Select MIRROR for rear projection with the tabletop-mounted projector. Select MIRROR INVERT for front projection with the ceiling-mounted projector. LAMP HOURS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The duration of illumination of a lamp converted in the Low mode is displayed. ON EN-16 3 FEATURE MENU POSITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . When AUTO is selected, the film mode will be automatically activated when a film source signal is inputted. MENU POSITION When OFF is selected, the film mode will not be actiCINEMA MODE AUTO vated. [. . . ] DSUB_ROUT DSUB_GOUT DSUB_BOUT NC GND GND GND GND NC GND GND NC DSUB_HOUT DSUB_VOUT NC Dimensional drawings (unit : mm) 256 What's included in the box AC power cord for US 02552-0063-01 for EU 02552-0066-01 for UK 02552-0065-01 02552-0072-00 02552-0068-00 1 1 1 2 1 1 Remote control Safety manual/Quick start up CD-ROM Battery Lens cap Soft case 1 RGB cable for PC 1 VIDEO cable Replacement part (Option / Not included in the box) Spare lamp VLT-XD206LP EN-28 102 223 Specification of RGB signals in each computer mode of the projector Signal mode TV60, 480I TV50, 576I 1080I 60 (1080I) 1080I 50 (1080I) 480P 576P 720P 60 (720P) 720P 50 (720P) PC98 (VGA56) CGA84 (VGA85) CGA85 (VGA85) VGA60 VGA72 VGA75 VGA85 SVGA56 SVGA60 SVGA72 SVGA75 SVGA85 XGA60 XGA70 XGA75 XGA85 SXGA70a(SXGA70) SXGA75a(SXGA75) SXGA60b(SXGA60) SXGA60 MAC13 (VGA67) MAC16 (SVGA75) MAC19 (XGA75) MAC21(SXGA75) HP75 (XGA75) SUN66a(SXGA66) SUN76a(SXGA76) resolution (H x V) 640 x 400 640 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1152 x 864 1280 x 960 1280 x 1024 640 x 480 832 x 624 1024 x 768 1152 x 870 1024 x 768 1152 x 900 1152 x 900 horizontal frequency (kHz) 15. 73 15. 63 33. 75 28. 13 31. 47 31. 25 45. 00 37. 50 24. 82 37. 86 37. 86 31. 47 37. 86 37. 50 43. 27 35. 16 37. 88 48. 08 46. 88 53. 67 48. 36 56. 48 60. 02 68. 68 63. 85 67. 50 60. 00 63. 98 35. 00 49. 72 60. 24 68. 59 62. 94 61. 85 71. 81 vertical frequency (Hz) 59. 94 50. 00 60. 00 50. 00 59. 94 50. 00 60. 00 50. 00 56. 42 84. 13 85. 08 59. 94 72. 81 75. 00 85. 01 56. 25 60. 32 72. 19 75. 00 85. 06 60. 00 70. 07 75. 03 85. 00 70. 01 75. 00 60. 00 60. 02 66. 67 74. 55 75. 02 74. 96 74. 92 66. 00 76. 64 XD206U (H x V) 1024 x 768 1024 x 768 1024 x 576 1024 x 576 1024 x 768 1024 x 768 1024 x 576 1024 x 576 1024 x 640 1024 x 640 1024 x 640 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 960 x 768 1024 x 768 1024 x 768 1016 x 768 1024 x 768 1024 x 768 984 x 768 984 x 768 Important: · · Some computers aren't compatible with the projector. It may not display images of higher resolutions than 1024 x 768 correctly. If the resolution and frequency of your computer aren't shown on the table, find the compatible resolution and frequency by changing the resolution of your computer. Set COMPUTER INPUT in the SIGNAL menu to RGB when inputting the HDTV signal as RGB signal. · · · · · · · TV60 and TV50 are equivalent to 480I and 576I respectively. [. . . ]