User manual MITSUBISHI XD20A

[. . . ] Data Projector User Manual English IMPORTANT Digital Light Processing, DLP, Digital Micromirror Device and DMD are all trademarks of Texas Instruments. Windows 98, Windows 95, and Windows 3. 1 are registered trademarks in the United States and other countries of Microsoft Corporation. IBM is a registered trademark of International Business Machines Corporation. Other names of companies and products mentioned are trademarks and registered trademarks of the respective companies. [. . . ] Down VIDEO EO S VID r / YCbC RGB Change the unit setting to suit the method and source selected in step 4. · Select the "PROJECTION" appropriate for the type of projector installation. (See page 29) If the image is projected reversed, vertically, or horizontally, reset "PROJECTION". · In the case of video or S-video, select the color system as necessary. (See page 26) Normally, it is not necessary to change the factory settings. (See page 27) O AUDI SE MOU Up 2 · In the case of RGB input, adjust the video of the connected PC. This projector automatically identifies the input signal and selects the most appropriate resolution. However, manually adjust the "PICTURE ADJ" and "FINE PICTURE" (see page 24) when there is flicker, noise, color offset, etc. , and manually adjust the vertical and horizontal position (see page 24) when the image is not centered. You can also choose to project the image at the original size of the incoming signal resolution. (Normally, the resolution is automatically sensed and the display is enlarged or reduced. ) 1 6 When distortion of the projected image cannot be corrected with the adjusters, press the KEYSTONE +/­ buttons of the remote control to fine adjust (see page 18). Using KEYSTONE to adjust projected image distortion. ZOOM KEYSTONE VOLUME Note Maximum correction is 14 degrees (including optical correction). E ­ 15 N OPE (Continued on the next page. ) Using the unit (continued) Using the Remote Control (Input Selection) 9 10 Adjust the picture elements (see page 22), then select the picture type according to the video content (see page 26). MOUSE MENU POWER Start using the unit. The following functions are available while using the unit: · Adjusting the volume of the unit's speaker (see pages 18 and 28), · Turning off the image and muting the sound temporarily (see page 18), · Freezing a moving picture (see page 18), · Enlarging the picture (see page 19) Note · When there is no signal input for a period of 5 min. or more, the power is automatically turned off and standby status is activated. (see page 29) VIDEO button VIDEO CANCEL RGB RGB button Operating from the main unit Inputs can be selected not only by operating the remote control but also by using the main unit SOURCE button. POWER STATUS POWER SOURCE AUTO SOURCE button 1 Press the VIDEO button. The video signal (VIDEO, S-VIDEO) connected to the input jack of this device will be detected and projected automatically. If a video signal is not detected, the message NO SIGNAL will be displayed. After using the unit VIDEO 1 Press the POWER button of the remote control or the POWER button of the main unit for a few seconds. The power will turn off and the POWER indicator will blink amber for 1 min. , then the standby status will be activated. (The exhaust fan will continue to run for a while for cooling purposes. ) Do not unplug the power cord while the indicator is blinking. MOUSE MENU VIDEO CANCEL RGB POWER POWER ST 2 Press the RGB button. The analog RGB signal connected to the input connector of this device will be detected and projected automatically. (Component video will be detected if the RGB/ YCbCr connector is set (page 27) to YCbCr. ) If a video signal is not detected, the message NO SIGNAL will be displayed. RGB POWER Note Blinks amber (1 min. ) Lights amber Note · All video signals input to this device will be detected if Auto Source (page 29) is set. 3 Press the SOURCE button. The video signal (RGB or YCbCr, VIDEO, SVIDEO) connected to the input jack of this device will automatically be detected and projected. If a video signal is not detected, the message NO SIGNAL will be displayed. SOURCE · The POWER switches of the remote control and main unit will not operate until the blinking stops. · The exhaust fan will continue to run even in standby status. 2 Disconnect the power cord. The POWER indicator will turn off. RGB/YCbCr S-VIDEO VIDEO Note · When Auto Source (see page 29) is set to ON, all signals input to this projector will be sensed. E ­ 16 Using the Mouse Remote Control as the PC The remote control of this projector can be used as the PC mouse (wireless mouse function) by connecting the MOUSE connector of this projector and the PC. Remote control mouse functions · When the MOUSE button on the remote control is pressed, the button is lit in red. This red light shows that the cursor key on the remote control operates the computer mouse function. When the MOUSE button is pressed again, the button's light goes off. In this condition the cursor key operates the projector cursor function. MOUSE button · If a computer running Windows is connected, the ENTER button on the remote control operates as the computer mouse left click button and the CANCEL button as the computer mouse right click button. · If a Macintosh computer is connected, the ENTER and CANCEL buttons operate in the same way as the computer mouse click button. MOUSE POWER MENU VIDEO RGB CANCEL Connecting a PC and the MOUSE connector of this projector Before connecting a PC · Before connecting, turn off the PC power. · When connection is completed, turn on the power of this projector and then start the PC. USB Port Connection Connect the supplied USB mouse cable directly to the USB port (universal serial bus) of the personal computer, as shown in the diagram. [. . . ] If you try to turn on the unit immediately after turning off, sometimes the power does not come on. If this happens, wait at least one minute, then turn on the unit again. · The lamp lighting voltage error detection protector has been triggered. If this does not solve the problem, please contact your dealer. Flashing Slowly (On and off in a cycle of 8 sec. ) Flashing Very Slowly (On and off in a cycle of 12 sec. ) The cooling fan has stopped. [. . . ]