User manual MITSUBISHI XD221U

[. . . ] EN DATA PROJECTOR MODEL XD221U User Manual This User Manual is important to you. Please read it before using your projector. ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. [. . . ] The operating sound is consequently reduced, and the lamp lifetime becomes longer. · If this mode is frequently switched, the lamp may be deteriorated. If AUTO is selected, selects AUDIO 1 when the input source is COMPUTER, while selects AUDIO 2 when the input source is VIDEO/SVIDEO. ance of AUDIO 1/AUDIO 2 using MIX When this mode is set to ON, the lamp is automatically lit when the power cord is plugged in the wall outlet. Selects a desired timer setting until the projector enters the standby mode when there is no signal input from the source. Select ON to display the splash screen when the projector is powered on. Selects the background color that is displayed when there is no signal input from the source. Select this setting when you want to view images from the front with the projector set on the floor. Select this setting when you want to view images from behind the screen with the projector set on the floor. Select this setting when you want to view images from behind the screen with the projector set at the ceiling. Select this setting when you want to view images from the front with the projector set at the ceiling. Resets LAMP TIME. opt. INSTALLATION WALL SCREEN LAMP MODE STANDBY MODE AUDIO INPUT AUTO POWER ON AUTO POWER OFF ON WALL SCREEN BEIGE STANDARD STANDARD AUTO OFF OFF ON BLUE OFF OK LAMP MODE LOW SPLASH SCREEN BACK COLOR IMAGE REVERSE LAMP TIME RESET STANDARD STANDBY MODE LOW AUTO AUDIO INPUT AUDIO 1/AUDIO 2 MIX AUTO POWER ON ON/OFF AUTO POWER OFF SPLASH SCREEN BACK COLOR OFF/5-60 min ON/OFF BLUE/BLACK OFF MIRROR IMAGE REVERSE INVERT MIRROR INVERT LAMP TIME RESET OK · By default, the LAMP MODE is set to STANDARD. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected, and you cannot switch the LAMP MODE in about one minute after the lamp is on. EN-20 Menu operation (continued) 3. FEATURE menu Menu option Setting NORMAL ASPECT Feature description Automatically sets the aspect ratio in relative to the input signal. Selects a desired screen position for anamorphically squeezed or horizontally compressed images stored on DVD disks. You can select from CENTER, UPPER, and LOWER by pressing the ENTER button. Select this setting when you want to project images in the full screen. Select Auto to automatically activate the film mode when the input video signal is a video signal from a film. Select Auto to automatically set the appropriate video format in relative to the input signal. If projected images aren't displayed correctly, select a desired video format manually. Select the appropriate format when the input signal is a WXGA video signal and the "AUTO" mode does not display images properly. Select "OFF" when the input signal is other than a WXGA video signal. [. . . ] 3. 2 kg 114 inch (1. 8 m) +41°F (+5°C) - +95°F (+35°C), 30 - 90% Video compatibility Speaker S-video input Video input Audio input Analog RGB input PBPR/CBCR:0. 7 Vp-p Control connector Outside dimensions Weight Length of power cord Temperature, humidity (performance guaranteed) · The specifications and outside appearance of the projector are subject to change without prior notice. EN-33 ENGLISH Type DLPTM DATA projector Specifications (continued) Connectors COMPUTER IN/OUT (Mini D-SUB 15-pin) 11 15 6 10 1 IN pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND DDC5V GND GND DDC Data HD/CS VD DDC Clock 5 OUT pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND HD/CS VD - Dimensional drawings (unit : mm) What's included in the box AC power cord for US J2552-0063-01 for EU J2552-0066-01 for UK J2552-0065-01 J2552-0072-03 1 1 1 2 1 Remote control Safety Manual/Quick Start up CD-ROM Battery Soft case 1 RGB cable for PC Replacement part (Option / Not included in the box) Spare lamp for XD221U VLT-XD221LP EN-34 Specifications (continued) Specification of RGB signals in each computer mode of the projector Signal mode TV60, 480i (525i) TV50, 576i (625i) 1080i 60 (1125i 60) 1080i 50 (1125i 50) 480p (525p) 576p (625p) 720p 60 (750p 60) 720p 50 (750p 50) CGA84 CGA85 VGA60 VGA72 VGA75 VGA85 SVGA56 SVGA60 SVGA72 SVGA75 SVGA85 XGA60 XGA70 XGA75 XGA85 SXGA70a SXGA75a WXGA60 WXGA60a WXGA60b WXGA60c SXGA60b SXGA60 MAC13 MAC16 MAC19 HP75 SUN66a SUN76a resolution (H x V) 640 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1152 x 864 1280 x 768 1280 x 800 1360 x 768 1366 x 768 1280 x 960 1280 x 1024 640 x 480 832 x 624 1024 x 768 1024 x 768 1152 x 900 1152 x 900 horizontal frequency (kHz) 15. 73 15. 63 33. 75 28. 13 31. 47 31. 25 45. 00 37. 50 37. 86 37. 86 31. 47 37. 86 37. 50 43. 27 35. 16 37. 88 48. 08 46. 88 53. 67 48. 36 56. 48 60. 02 68. 68 63. 85 67. 50 47. 77 49. 70 47. 71 47. 50 60. 00 63. 98 35. 00 49. 72 60. 24 62. 94 61. 85 71. 81 vertical frequency (Hz) 59. 94 50. 00 60. 00 50. 00 59. 94 50. 00 60. 00 50. 00 84. 13 85. 08 59. 94 72. 81 75. 00 85. 01 56. 25 60. 32 72. 19 75. 00 85. 06 60. 00 70. 07 75. 03 85. 00 70. 01 75. 00 59. 87 59. 81 60. 01 59. 75 60. 00 60. 02 66. 67 74. 55 75. 02 74. 92 66. 00 76. 64 XD221U (H x V) 1024 x 768 1024 x 768 1024 x 576 1024 x 576 1024 x 768 1024 x 768 1024 x 576 1024 x 576 1024 x 640 1024 x 640 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 614 1024 x 640 1024 x 578 1024 x 575 1024 x 768 960 x 768 1024 x 768 1024 x 768 1016 x 768 1024 x 768 984 x 768 984 x 768 *1 *1 *1 *1 *2 *2 *2 *2 *2 *2 *2 *2 *2 *1 When you input the signals WXGA60, WXGA60a, WXGA60b, , or WXGA60c, select the supported image size from WXGA of the FEATURE menu. *2 The partial enlargement feature is not supported. Important: · · · · · Some computers aren't compatible with the projector. [. . . ]