User manual MITSUBISHI XD250U-ST

[. . . ] EN DATA PROJECTOR MODEL XD250U-ST User Manual This User Manual is important to you. Please read it before using your projector. ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. [. . . ] Use this setting to adjust projected images when flagging occurs in the upper area of the screen. opt. SIGNAL HORIZ. TRACKING RGB RGB 0 0 0 0 RGB 100% OFF OK COMPUTER INPUT OVER SCAN HOLD USER opt. SIGNAL USER CLAMP POSITION CLAMP WIDTH VERT. LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 1 1 AUTO OFF 0 0 0 0 SIGNAL USER menu · · · · · · Horizontal strips may appear in the enlarged projected image, though these conditions are not a malfunction. When you change the value of the horizontal or vertical position drastically, noise may appear. The adjustable range of the vertical position varies depending on the type of the input signal. When you increase the value of OVER SCAN, noise may appear on the screen. You can set the IMAGE, SIGNAL, and SIGNAL-USER menus only when the signal is input. Important: 5. PROJECTOR NAME SET NETWORK PASSWORD IP CONFIG DHCP OK OK ON / OFF Setting Feature description Displays PROJECTOR NAME. Use this setting when you obtain IP CONFIG automatically by DHCP server. However, IP ADDRESS is not set as factory default, and cannot be displayed. However, SUBNET MASK is not set as factory default, and cannot be displayed. However, DEFAULT GATEWAY is not set as factory default, and cannot be displayed. Resets the Network Setting. opt. NETWORK PROJECTOR NAME NETWORK PASSWORD IP CONFIG PJLink CERTIFICATION NETWORK RESET SET OK OK ON OK opt. ***, ***, ***, *** IP ADDRESS SET ***, ***, ***, *** SUBNET MASK SET ***, ***, ***, *** DEFAULT GATEWAY SET MAC ADDRESS PJLink CERTIFICATION NETWORK RESET xx-xx-xx-xx-xx-xx ON / OFF OK NETWORK IP CONFIG DHCP IP ADDRESS SUBNET MASK DEFAULT GATEWAY MAC ADDRESS ON 192. 168. 0. 10 255. 255. 255. 0 10. 132. 1. 1 xx-xx-xx-xx-xx-xx NETWORK IP CONFIG menu EN-23 ENGLISH Menu operation (continued) 6. INFORMATION menu Menu option Feature description This menu shows a lamp operating time (hour) calculated assuming that LAMP MODE is LOW. · When the LAMP MODE is STANDARD, this menu shows a longer lamp operating time than the actual time. (See page 34 for the interval of lamp replacement. ) · When the lamp operating time is 0 to 10 hours, "0H" is displayed. When the lamp operating time exceeds 10 hours, the actual hours are displayed. · When the lamp operating time reaches 4500 hours, the bar turns yellow. (The lamp lifetime is 6000 hours. ) Indicates the name of the terminal to which the currently projected video signal is being input. Indicates the vertical frequency of the currently projected video signal. Indicates the horizontal frequency of the currently projected video signal. Indicates the type of the sync signal for the currently projected video signal. opt. INFORMATION 0H LAMP TIME (LOW) LAMP TIME (LOW) INPUT RESOLUTION VERTICAL FREQUENCY HORIZONTAL FREQUENCY RGB H V COMPUTER2 1024x768 75. 04 Hz 60. 02 KHz 5wire INPUT RESOLUTION VERTICAL FREQUENCY HORIZONTAL FREQUENCY SYNC. [. . . ] 3. 4 kg 114 inch (1. 8 m) +41°F (+5°C) - +95°F (+35°C), 30 - 90% · The specifications and outside appearance of the projector are subject to change without prior notice. EN-39 ENGLISH Type DLPTM DATA projector Specifications (continued) Connectors COMPUTER IN/OUT (Mini D-SUB 15-pin) HDMI IN (HDMI 19-pin) 11 15 1 19 6 10 1 IN pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND DDC5V GND GND DDC Data HD/CS VD DDC Clock 5 OUT pin No. TMDS Data2+ TMDS Data2 Shield TMDS Data2TMDS Data1+ TMDS Data1 Shield TMDS Data1TMDS Data0+ TMDS Data0 Shield TMDS Data0TMDS Clock+ TMDS Clock Shield TMDS ClockCEC SCL SDA DDC Ground +5 V Power Hot Plug Detect Dimensional drawings (unit : mm) 325 What's included in the box AC power cord for US J2552-0063-03 for EU J2552-0066-02 for UK J2552-0065-02 J2552-0072-03 1 1 1 2 1 1 Remote control Safety Manual/Quick Start up CD-ROM Battery Lens cap Soft case 1 RGB cable for PC Replacement part (Option / Not included in the box) Spare lamp for XD250U-ST VLT-XD280LP EN-40 118 251 Specifications (continued) Specification of RGB signals in each computer mode of the projector Signal mode TV60, 480i (525i) TV50, 576i (625i) 1080i 60 (1125i 60) 1080i 50 (1125i 50) 480p (525p) 576p (625p) 720p 60 (750p 60) 720p 50 (750p 50) CGA84 CGA85 VGA60 VGA72 VGA75 VGA85 SVGA56 SVGA60 SVGA72 SVGA75 SVGA85 XGA60 XGA70 XGA75 XGA85 SXGA70a SXGA75a WXGA60 WXGA60a WXGA60b WXGA60c SXGA60b SXGA60 MAC13 MAC16 MAC19 HP75 SUN66a SUN76a resolution (H x V) 640 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1152 x 864 1280 x 768 1280 x 800 1360 x 768 1366 x 768 1280 x 960 1280 x 1024 640 x 480 832 x 624 1024 x 768 1024 x 768 1152 x 900 1152 x 900 horizontal frequency (kHz) 15. 73 15. 63 33. 75 28. 13 31. 47 31. 25 45. 00 37. 50 37. 86 37. 86 31. 47 37. 86 37. 50 43. 27 35. 16 37. 88 48. 08 46. 88 53. 67 48. 36 56. 48 60. 02 68. 68 63. 85 67. 50 47. 77 49. 70 47. 71 47. 50 60. 00 63. 98 35. 00 49. 72 60. 24 62. 94 61. 85 71. 81 vertical frequency (Hz) 59. 94 50. 00 60. 00 50. 00 59. 94 50. 00 60. 00 50. 00 84. 13 85. 08 59. 94 72. 81 75. 00 85. 01 56. 25 60. 32 72. 19 75. 00 85. 06 60. 00 70. 07 75. 03 85. 00 70. 01 75. 00 59. 87 59. 81 60. 01 59. 75 60. 00 60. 02 66. 67 74. 55 75. 02 74. 92 66. 00 76. 64 XD250U-ST (H x V) 1024 x 768 1024 x 768 1024 x 576 1024 x 576 1024 x 768 1024 x 768 1024 x 576 1024 x 576 1024 x 640 1024 x 640 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 614 1024 x 640 1024 x 578 1024 x 575 1024 x 768 960 x 768 1024 x 768 1024 x 768 1016 x 768 1024 x 768 984 x 768 984 x 768 *1 *1 *1 *1 *2 *2 *3 *2 *3 *2 *2 *2 *2 *2 *2 *1 When you input the signals WXGA60, WXGA60a, WXGA60b, or WXGA60c, select the supported image size from WXGA of the FEATURE menu. *3 The HDMI IN terminal is not available for these signals. Important: · · · · · Some computers aren't compatible with the projector. [. . . ]