User manual MITSUBISHI XD490U

[. . . ] DLPTM PROJECTOR MODEL XD490U XD460U User Manual This User Manual is important to you. Please read it before using your projector. XD490 XD460 ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable and RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class B device. [. . . ] * 9: Available only when the input signal is from the VIDEO IN or S-VIDEO IN terminal. 0 - 999 *6 0 - 999 *6 0 - 31 0 - 9999 *6 AUTO, RGB, YCBCR / YPBPR BEGIN OFF ON END USER OK CLAMP POSITION *7 CLAMP WIDTH *7 1: Not available when COLOR ENHANCER is set to sRGB. OVER SCAN 3: Setting range differs depending on the setting of SCREEN SIZE. SHUTTER (U) 5: Available only when the source is a COMPUTER/COMPONENT SHUTTER (L) SHUTTER (LS) VIDEO IN1. SHUTTER (RS) 6: Setting range differs depending on the input signals. *8 *8 *8 *2 *2 *2 *2 0 - 99 0 - 99 1 - 63 1 - 63 AUTO, OFF 100 - 90% ON , OFF 0 - 38 0 - 38 0 - 63 0 - 63 *2 *6 How to set the menus: Following describe how to set AUTO POWER OFF time. · When no signal is input, the menu does not appear. opt. 4. Press the or button to select an item to adjust. OFF OFF AUTO POWER ON AUTO POWER OFF 5. Set the selected item by pressing the AUTO POWER ON AUTO POWER OFF OFF 30min or button. XGA60 IMAGE 2. Press the opt. or button to select a menu to use. XGA60 To cancel the menu: 6. Important: · When the MENU button doesn't function, unplug the power cord from the wall outlet. · After selecting the items marked with , press the ENTER button. INSTALLATION 3. Press the ENTER button (or AUTO POWER ON AUTO POWER OFF OFF OFF button). EN-22 Available settings in the menus Set the following items on their relevant menus. 1. SIGNAL menu opt. opt. XGA60 FEATURE BEIGE OFF STANDARD OFF OFF ON BLUE OFF AË XGA60 SIGNAL AUTO DISPLAY INPUT 1. AUTO AUTO AUTO OFF English OK RGB RGB XGA60 0 0 0 0 RGB OFF OK IMAGE COLOR ENHANCER CONTRAST BRIGHTNESS COLOR TEMP. COLOR TINT SHARPNESS INSTALLATION WALL SCREEN VIRTUAL LENS SHIFT LAMP MODE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN BACK COLOR IMAGE REVERSE ASPECT PASSWORD FUNCTION MENU POSITION CINEMA MODE ? HORIZ. TRACKING COMPUTER INPUT HOLD USER VIDEO SIGNAL SET UP SCART INPUT LANGUAGE RESET ALL 1. IMAGE menu ITEM SETTING COLOR ENHANCER AUTO PRESENTATION STANDARD THEATER sRGB USER ±30 ±30 4 options ±10 ±10 ±5 CONTRAST BRIGHTNESS COLOR TEMP. COLOR TINT SHARPNESS FUNCTION Select to optimize the settings automatically depending on the input signal. (Select this option for normal use. ) Select to make the displayed image look bright and crisp. This option, suitable for viewing movies, makes the displayed image look soft and smooth. · When COLOR ENHANCER is sRGB, COLOR TEMP. , COLOR and TINT can't be adjusted. (See page 26. ) Use to adjust the color thickness of the projected image. (See page 25. ) · When the TV50 (PAL, SECAM) signal is input, TINT can't be adjusted. [. . . ] When they are supplied to the COMPONENT terminal, the signal mode is indicated as 480i or 576i. · Video signals having resolution exceeding the maximum resolution supported by this projector are reduced to the maximum resolution size of the projector even in the REAL mode. · This projector doesn't support 480i, 576i, and 480p signals from video devices having 5 lines (R, G, B, H, V). EN-38 SERIAL (8-pin) 12 10 5 1 Pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND DDC 5V GND GND DDC Data HD/CS VD DDC Clock 16 9 6 15 11 3 5 1 2 3 4 5 6 8 1 PIN No. [. . . ]