User manual MITSUBISHI XD90

[. . . ] DATA PROJECTOR MODEL XD90U User Manual XD90U This User Manual is important to you. Please read it before using your projector. ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of suffcient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOITURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. EN-2 WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. [. . . ] For details of the on-screen menu operation, please refer to "Using the menus" on page 30 for information. WARNING: You will be inconvenienced if you activate the password functionality and subsequently forget the password. Print out this manual and write the password you used in this manual, and keep the manual in a safe place for later recall. To set a password CAUTION: Once a password has been set, the projector cannot be used unless the correct password is entered every time the projector is started. 1. Open the on-screen menu and go to pressing the3Left or4Right button. Setting > Password. Select On by 2. Password Setup When the function is activated for the first time, a prompt will display on the screen. Use the 5 Enter Password 0 0 0 0 or 6Down button to select a number for each Press Auto to Confirm digit of the password. Use the3Left or4Right Press 5 or 6 to change number button to move between the digits of the Press 3 or 4to move password. 3. When all digits are entered and the password is ready, press the AUTO button to confirm. A confirmation message displays. Password Setup Do you want to use 0 0 0 0 as your password?Yes Auto No 5 Cancel 6 · · The password will display on-screen when being input. IMPORTANT: Write your selected password down here in this manual so that it is available to you should you ever forget it. · · · You have the following options: Press AUTO to continue. The set-up is finished when the message "Password setup completed" displays. Press the 5Up button to go back to the previous screen and re-enter four digits. Press the 6Down button to cancel the password set-up and return to the on-screen menu. If you forget the password Once activated, you will be asked to enter the four-digit password every time you turn on the projector. You can retry by turning off the projector (by pressing the Power button) and start again, or if EN-23 ENGLISH You can also press the SOURCE button to select your desired input signal manually. For more information, please refer to "Switching input signal" on page 27. you did not record the password in this manual, and you absolutely do not remember it, you can use the password recall procedure. To enter the password recall procedure Press and hold the4Right button for 5 seconds. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. To change the password 1. · Open the on-screen menu and go to Setting > Change Password. If the password is correct, you can go on to enter new password. IMPORTANT: Write your selected password down here in this manual so that it is available to you should you ever forget it. Password: __ __ __ __ Keep this manual in a safe place. · 4. · · · If the password is incorrect, a "Password Error" message displays. Press the 5Up button to try again or press the 6Down button to cancel. You have the following options: Press the AUTO button to complete the procedure. Press the 6Down button to cancel the set-up and return to the on-screen menu. Adjusting the height The projector is equipped with one quick-release adjuster foot and one rear adjuster foot. [. . . ] Adjust the projection angle and direction as well as the height of the unit if necessary. See "Obtaining a preferred projected image size" on page 13 for details. Slide open the lens cover. EN-44 Remote control does not work. Cause The battery is out of power. You are too far away from the projector. Remedy Replace the battery with a new one. [. . . ]