User manual MITSUBISHI XL2550U

[. . . ] LCD PROJECTOR MODEL XL2550U XL1550U User Manual XL2550 XL1550 This User Manual is important to you. Please read it before using your projector. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power supply cord, it may cause interference with radio and television reception. Use the attached RGB cable and RS-232C cable and the shielded LAN cable with this equipment so as to keep interference within the limit of a FCC Class B device. [. . . ] Select when viewing images projected from the behind of the screen with the projector installed on the ceiling. Select when viewing images from the front with the projector installed on the ceiling. AUTO POWER ON ON / OFF AUTO POWER OFF IMAGE CAPTURE SPLASH SCREEN BACK COLOR MUTE MODE IMAGE REVERSE OFF / 5-60min ON / OFF BLUE / BLACK / IMAGE BLACK / IMAGE OFF MIRROR INVERT MIRROR INVERT · · · · Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 1 minute after turn-on. You can't set IMAGE CAPTURE and SPLASH SCREEN when PASSWORD FUNCTION in the FEATURE menu has been set to SPLASH ID SCREEN to enable the password lock. When you continue projection for a long time with BACK COLOR or MUTE MODE set to IMAGE, an afterimage may persist on the screen. FEATURE menu opt. FEATURE ASPECT PASSWORD FUNCTION MENU POSITION CINEMA MODE ? AUTO DISPLAY INPUT 1. AUTO AUTO AUTO OFF English OK VIDEO SIGNAL SETUP SCART INPUT AË LANGUAGE RESET ALL ITEM ASPECT SETTING AUTO 16:9 REAL FULL PASSWORD FUNCTION MENU POSITION CINEMA MODE VIDEO SIGNAL SETUP 2 options AUTO OFF 8 options AUTO OFF 3. 75% / 7. 5% ON / OFF SCART INPUT LANGUAGE RESET ALL · · · · · 10 languages OK FUNCTION Select to change the aspect ratio automatically depending on the input signal. (Select this option for normal use. ) This option allows you to select the display position of squeezed (or horizontally compressed) images stored on DVD discs. By pressing the ENTER button, you can select the display position among CENTER, UPPER, and LOWER. Select to project images in full size (1024 x 768 pixels) irrespective of type of input signal. The film mode will be automatically activated when a film source signal is input. When AUTO is selected, the appropriate video format is automatically selected depending on the input signal. If the image isn't displayed correctly, select the desired video format manually. · When 7. 5% is chosen, the brightness is decreased by the set-up cancel function for the U. S. Choose ON when connecting the projector with a device equipped with the SCART terminal that can output RGB signal. (Available only for the input signal from the COMPUTER/COMPONENT VIDEO IN-1 terminal. ) Use to select the language used in the menus. Use to reset the settings of the menu (excluding IMAGE CAPTURE, PASSWORD FUNCTION and LANGUAGE) to the factory setting values. CINEMA MODE can be adjusted only when a TV60, TV50, 480i or 576i signal is being displayed. When SCART INPUT is set to ON, nothing is output to the external monitor. When SCART INPUT is set to ON, normal computer signals aren't projected. Use a commercially available SCART-Mini D-SUB 15-pin cable when connecting this projector with an AV device equipped with the SCART terminal. Some AV devices equipped with the SCART terminal aren't compatible with this projector. EN-25 Menu operation (continued) 4. SIGNAL menu opt. SIGNAL - RESOLUTION (MEMORIZE) menu opt. SIGNAL - USER menu opt. SIGNAL A U H V SIGNAL AUTO 1024x768 0 0 0 0 RGB 100% OFF OK SIGNAL USER 75. 04 Hz 60. 02 KHz 1024 768 OK OK ? MEMORY CALL RESOLUTION (MEMORIZE ) HORIZ. [. . . ] · For signals that are larger than the panel resolution, only their center part is displayed in the REAL mode. · In the REAL mode, images are black-framed when the image resolution is lower than 1024 x 768. EN-45 Specifications (continued) Connectors SERIAL (D-SUB 9-pin) 5 9 1 10 6 15 Pin No. 1 2 3 4 5 6 7 8 9 Name TXD RXD GND I/O IN OUT - COMPUTER/COMPONENT VIDEO IN-1/IN-2 (Mini D-SUB 15-pin) 5 1 Pin No. R(RED)/PR/CR G(GREEN)/Y B(BLUE)/PB/CB GND GND GND GND GND DDC 5V (*1) GND GND DDC Data (*1) HD/CS (*1) VD DDC Clock DVI-D (HDCP) (DVI-D 24-pin) 16 24 17 9 6 11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 8 1 PIN No. [. . . ]