User manual MITSUBISHI XL2U

[. . . ] LCD Projector User Manual XL2 MODEL XL2U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class B device. [. . . ] AUDIO MODE VIDEO SIGNAL SCART INPUT *4 ANAMORPHIC 3D CineView *5 LANGUAGE RESET ALL MEMORY CALL HORIZ. POSITION VERT. POSITION FINE SYNC. *4 TRACKING *4 COMPUTER INPUT *4 HOLD *4 1, 2, 3, OFF -20 - +30 *3 ON, OFF OFF, 5, 10, 15, 30, 60 min ON, OFF BLUE, LOGO, BLACK BLACK, LOGO STANDARD, LOW OFF, MIRROR, INVERT, MIRROR INVERT 1=Upper left, 2=Lower right (The item can not be selected when 1-4 the source is selected to COMPUTER) 1-5 COMPUTER, VIDEO, COMPUTER VIDEO, MUTE AUTO, NTSC, PAL, SECAM, 4. 43NTSC, PAL-M, PAL-N, PAL-60 ON, OFF OFF, CENTER, UPPER, LOWER ON, OFF , English, Español, Deutsch, Français, Italiano, , , , OK AUTO, USER1, USER2 0 - 999 *6 0 - 999 *6 0 - 39 0 - 9999 *6 RGB, YCBCR / YPBPR AUTO ON OFF FEATURE SIGNAL BEGIN END CLAMP POSITION *4 CLAMP WIDTH *4 HORIZ. SYNC SHUTTER (U) SHUTTER (L) SHUTTER(LS) SHUTTER(RS) -1 - -99 1 - 99 USER MEMORIZE DELETE DEFAULT USER1, USER2 USER1, USER2 * 1: The item can not be selected when the sRGB is set to ON. * 3: The allowable range of the adjustment value in the keystone adjustment will vary depending on the installation conditions. * 4: The item can not be selected when the source is selected VIDEO or S-VIDEO. * 5: The item can be selected only when the selected source is VIDEO or S-VIDEO or the inputted signal is TV50 or TV60. * 6: Setting range is different with certain signals. *6 0 - +63 *6 1 - 63 *6 0 - 9999 *6 0 - 9999 AUTO, ON, OFF 0 - 383 0 - 383 0 - 510 0 - 510 Basic operation Several settings can be adjusted using Menu. Press the { or } button to select AUTO POWER OFF. AUTO POWER ON AUTO POWER OFF OFF OFF 5. Press the $ or % button to adjust auto power off time. AUTO POWER ON AUTO POWER OFF OFF 30 min XGA60 IMAGE 2. · If the menu operation is not working, press the RESET button on the terminal board using a suitable sharp object, push gently. · The settings with mark, you should press the ENTER button after selecting. XGA60 INSTALLATION 3. Press the ENTER button (or } button). opt. XGA60 OFF 0 OFF INSTALLATION RIS KEYSTONE AUTO POWER ON EN ­ 15 ENGLISH IMAGE CONTRAST BRIGHTNESS sRGB COLOR MATRIX RED ± 30 ± 30 YELLOW ± 30 ± 30 GREEN ± 30 ON, OFF CYAN ± 30 VIDEO BLUE ± 30 COMPUTER ± 30 MAGENTA USER ±5 SATURATION RGB-TINT ± 20 OFF STANDARD CONTRAST R ± 30 HIGH CONTRAST B ± 30 LOW BRIGHTNESS R ± 30 USER BRIGHTNESS B ± 30 ± 10 (Displays only when the source is selected to VIDEO) ± 10 (Displays only when the source is selected to VIDEO) ± 10 AUTO, DYNAMIC, STANDARD, THEATER Menu operation (continued) 1 IMAGE opt. Select ON to display an image emphasizing on the color OFF sRGB reproducibility. COMPUTER COLOR MATRIX · When sRGB is ON, COLOR MATRIX, COLOR TEMP. (Available only when GAMMA MODE AUTO VIDEO is selected as the source. ) TINT . . . . . . . . . . . . . . . . . . . . The color balance of the image shifts green as the number increases and shifts to purple as the number decreases. (Available only when VIDEO is selected as the source. ) · When the TV50 (PAL, SECAM) signal is inputted, TINT can't be adjusted. When AUTO is selected, the appropriate gamma mode is automatically selected depending on the input signal. Adjusts the sensitivity of the function (RIS) which XGA60 automatically adjusts the brightness and contrast of the INSTALLATION image depending on the degree of the light in the room. When RIS OFF using this projector in a room where the light and shade KEYSTONE 0 AUTO POWER varies slightly, select 1. When using this projector in a OFF ON AUTO POWER OFF normally lighted room, select 2. When using this projector in OFF SPLASH SCREEN ON a room where the light and shade varies greatly, select BACK COLOR BLUE 3. When you select OFF, RIS won't operate. [. . . ] (Normal condition) Notes Off Off Steady green Blinking green Off The power button cannot be used to switch ON and OFF Steady green Steady green Off Abnormal condition POWER LAMP TEMP Steady green Steady green Blinking red CONDITION Unusual temperature · The ventilation slits or air filter is clogged with dust or debris. · The filter is dirty. POSSIBLE SOLUTIONS · Remove the object from the ventilation slits. · Clean the filter. Steady red Off Blinking red Steady red Blinking green Off The protection circuit is working or the lamp is in an abnormal condition. (The indicators operate as shown on the left at the time of power-off, too. In this case, they are'nt indicating an abnormal condision. ) · Wait until the LAMP indicator is turned off, then press the POWER button. [. . . ]