User manual MITSUBISHI XL30U

[. . . ] LCD Projector User Manual XL30 XL25 SL25 MODEL XL30U/XL25U/SL25U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class B device. [. . . ] XGA60 adjusts the brightness and contrast of the image depending on the degree of the light in the room. When using this projector in INSTALLATION a room where the light and shade varies slightly, select 1. When RIS OFF using this projector in a norually lighted room, select 2. When AUTO POWER OFF ON using this projector in a room where the light and shade varies AUTO POWER OFF OFF greatly, select 3. When you select OFF, RIS won't operate. SPLASH SCREEN ON · When the sensitivity is adjusted in a large amount, the BACK COLOR BLUE image may be displayed solid white. Adjust the sensitivity depending on the operating environment and imges to be MUTE MODE BLACK displayed. Select ON to boot up the projector automatically by turning on OFF IMAGE REVERSE an externally connected power switch such as a breaker even when the main power switch of the projector is off. · The projector will be in the stand-by mode when the lamp is off. Set the time elapsed before the projector enters into the stand-by mode when there is no signal inputted from the selected source. Use to select the background, BLUE, BLACK or LOGO, which will be displayed when there is no signal inputted from the selected source. Use to select the background, BLACK or LOGO, which will be displayed when the MUTE button is pressed. When LOW is selected, the image will become darker, though the power will be saved, operating sound will be reduced. · The intensity of the lamp will be STANDARD for 2 minutes regardless of the setting of the LAMP MODE when the lamp turns on. Select MIRROR, INVERT in rear projection with the projector hanging from the ceiling. · When no signal is supplied for 6 hours with BACK COLOR set to BLACK, it changes to BLUE automatically for the purpose of protecting the projector. · When you continue projection for a long time with BACK COLOR or MUTE set to LOGO, an after-image may persist on the screen. · When the signal is lost during muting with MUTE set to LOGO, AUTO POWER OFF is ignored even though it is active. ON EN ­ 16 3 FEATURE MENU POSITION . . . . . . . Use to select the position of the menu on the screen, (upper left) or (lower right). When AUTO is selected, the appropriate video format is automatically selected depending on the input signal. If the image isn't displayed correctly, select the desired video format manually. Select ON when connecting with a device equipped with the SCART terminal that can output RGB signal. Select the desired position, UPPER, CENTER or LOWER when playing DVD discs containing data of letterboxed images. [. . . ] ASCII '0' '1' '2' '3' '4' '5' '6' '7' '8' '9' HEX 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h [Example] When setting the volume to 15 (standard value) (Figures and symbols enclosed in quotation marks are ASCII codes. ): Sending commands from the PC, etc. 30 30 56 4C 31 35 0D '0' '0' 'V' 'L' '1' '5' ' ' 30 30 56 4C 31 35 0D '0' '0' 'V' 'L' '1' '5' ' ' Command receipt confirmation (Command echo back) Status code from the projector Command for setting the volume Description 2 6) Keystone commands (Not executable in stand-by mode, while the Splash screen is projected or the MUTE is executed. ) The keystone commands are used for the keystone setting of this projector with the value. The value will vary depending on the installation conditions, etc. ) ITEM KEYSTONE ASCII KS HEX 4Bh 53h VALUE ±30 How to set the grade Use the ASCII codes to set the grade for setting data. ASCII HEX '+' 2Bh '­' 2Dh '0' 30h '1' 31h '2' 32h '3' 33h '4' 34h '5' 35h '6' 36h '7' 37h '8' 38h '9' 39h 7) Mute commands (Not executable in stand-by mode or while the Splash screen is projected. ) The mute commands are used for the mute setting of this projector with the 0(30h) and 1(31h). ITEM MUTE ASCII MUTE HEX 4Dh 55h 54h 45h VALUE 0 (OFF), 1 (ON) 8) Remote commands Some remote control operations can be achieved by the remote command codes. [. . . ]