User manual MUSE M-1010 MRW

[. . . ] Before you install the unit, remove absolutely the two transportation screws on top of the unit. 7 8 9 10 11 Caution!- Make sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage the vehicle’s electrical system. - Make sure to connect the speaker (-) leads to the speaker (-) terminal. [. . . ] Otherwise, abnormality occurs on the display or some keys will not function properly. GB - 4 GB - 5 GB - 6 GB - 7 AR-3108 IB MUSE 001 REV0 GB. indd1 1 2011-8-23 10:09:35 LISTENING TO THE RADIO Selecting band In tuner mode, repeatedly press BAND/ LOUD button to select bands in following order: FM1->FM2->FM3. Manual/automatic tuning - Manual Tuning Press and hold button or until “MANUAL” shows on display, then press button or continuously to select a station upward or downward. - Automatic Tuning Press or once, the radio automatically searches a station upward or downward respectively and plays when it finds a station. Scanning/memorizing stations automatically - By SCH/AMS button In tuner mode, press and hold SCH/AMS button for 3 seconds to start scanning for stations and store them automatically in memory. Press SCH/AMS button, the radio plays each preset station for a few seconds. Press SCH/AMS again or numeric buttons 1-6 to listen to corresponding station. Press and hold one of the 1- 6 Number buttons for 2 seconds until LCD shows the corresponding number, which indicates that station is stored in the corresponding number button. Under radio mode, press 1- 6 Number buttons to listen to stored stations. When you are listening to a station stored on a number button, press and hold another number button for more than 2 seconds to store the station on this number button. -- RDS (Radio Data System) Operations -This unit has a built-in RDS decoder system that supports broadcast stations transmitting RDS data. This system can display the name of the broadcast station being received and can automatically switch to the broadcast station with the best reception as you travel on long distances (AF switching). A traffic announcement broadcast from a RDS station, no matter what mode you are. Additionally, if EON information is received, enables automatic switching of other preset stations on the same network and interruption of the station being received with traffic information. This function is not available in some areas. Alternative frequency (AF) The AF function switches to a different frequency on the same network in order to maintain optimum reception. In FM mode, press AF button, certain program will be automatically searched and received. If the reception of the current broadcast station deteriorates, “AF” appears in the display and the radio searches for the same program on another frequency. Press and hold AF button for 3 seconds, the unit will be under “REG ON” or “REG OFF” mode: REG ON: Should be selected to list the local broadcast of the current station, even if there is a national broadcast of this station. REG OFF: Should be selected to listen to the national broadcast of the current station. Traffic alarm (TA) In the TA standby mode, when a traffic announcement broadcast starts, the traffic announcement broadcast is received as top priority regardless of the function mode so you can listen to it. Press TA button, when LCD shows “TA”, traffic program will be automatically searched and saved, when LCD shows “TP”, this means that the RDS broadcast station being received has traffic announcement programmes. If you press TA button while a traffic announcement broadcast is being received, the traffic announcement broadcast reception is cancelled and the unit goes into the TA standby mode. ALARM “ALARM”will be displayed when an emergency broadcasting is received; meanwhile sound output level will be adjusted to the preset output level automatically when the volume control is set at minimum. [. . . ] Cleaning the Connector If the connector between the main unit and the front panel is dirty, may result in abnormal working condition. To avoid such problems, please detach the front panel, and clean the connector with an alcohol swab. Gently clean and avoid damaging the connector. Note: Due to continuous product improvement, specifications and design are subject to change without prior notice. To prevent any accident due to this type of beam, the set should only be opened by properly trained personnel. [. . . ]