User manual NAD C165BEE

[. . . ] ® Owner's Manual Stereo Preamplifier C 165BEE SVENSKA NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS ENGLISH IMPORTANT SAFETY INSTRUCTIONS ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA Save theSe inStructionS for later uSe. 1 read instructions - All the safety and operating instructions should be read before the product is operated. 2 retain instructions - The safety and operating instructions should be retained for future reference. 3 heed warnings - All warnings on the product and in the operating instructions should be adhered to. [. . . ] Typically, when the capacitance is too low, the upper midrange (the soprano voice range) will be softened and the response at the highest frequency will be peaky, leading to edgy violin tone and increased surface noise. Too high a value of capacitance will bring the upper midrange forward while rolling off the extreme highs. 5 phono ground connector: Turntables normally includes a single wire earth lead. 6 mc-mm Switch: Slide this switch to either MM (Moving Magnet) or MC (Moving Coil) depending upon the phono cartridge being used. Use a twin RCA-to-RCA lead to connect the CD player's left and right "Audio Outputs" to this input. Use a twin RCA-to-RCA lead to connect the tuner left and right "Audio Outputs" to this input. 9 mp input: Input for a Media Player or other line-level signal source. Use a twin RCA-to-RCA lead to connect the Media Player's left and right "Audio Outputs" to this input. 10 aux input: Input for additional line level input signals such as another CD player. Use a twin RCA-to-RCA lead to connect the auxiliary unit's left and right "Audio Outputs" to this input. 11 tape 2 in/out: Connections for analog recording and playback to an audio tape recorder of any type. Using twin RCA-to-RCA leads, connect to the left and right "Audio Output" of the tape machine to the TAPE 2 IN sockets for playback. Connect the left and right "Audio Input" of the tape machine to the TAPE 2 OUT sockets for recording. SVENSKA NEDERLANDS DEUTSCH ITALIANO 1 mc loadS (r1, r2, r3): If you are using a Moving Coil (MC) cartridge, set this switch to a resistive load that closely approximates the value specified in the MC cartridge (this is usually specified in the MC cartridge). In general, use the lowest resistance for low output cartridges and high resistance for medium output cartridges. For very high output models up to 1 mV/cm/sec and internal resistance as high as 200 ohms, use the low or medium input resistance as you may otherwise run into overload. 3 mc input: Input for a Moving Coil phono cartridge. Connect the twin RCA lead from your turntable to this input if you are using a Moving Coil cartridge. Connect the twin RCA lead from your turntable to this input if you are using a Moving Magnet cartridge. ESPAÑOL ATTENTION! PleasemakesurethattheC165BEEispoweredofforunpluggedbeforemakinganyconnections. Itisalsoadvisabletopowerdownorunplugall associatedcomponentswhilemakingorbreakinganysignalorACpowerconnections. FRANÇAIS ENGLISH IDENTIFICATION OF CONTROLS rear panel ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA 12 tape mon. in/out: Connections for analog recording and playback to a secondary audio tape recorder of any type. Using twin RCA-to-RCA leads, connect to the left and right "Audio Output" of the tape machine to the TAPE MONITOR IN sockets for playback and tape monitoring. Connect the left and right "Audio Input" of the tape machine to the TAPE MONITOR OUT sockets for recording. to make a recording When any source is selected, its signal is also fed directly to any tape machine connected to the TAPE 2 OUT or TAPE MONITOR OUT for recording. tape to tape copYing You can copy between two tape machines connected to your NAD C 165BEE. [. . . ] tuner control (for use with nad am/fm/dab tuner): Set the DEVICE SELECTOR to "TUN" in order to gain access to these buttons. Refer to the corresponding labels printed in the remote control faceplate and their respective assigned buttons to make use of these functions. Some of the control buttons below are applicable only to specific NAD Receiver or Tuner models; check the owner's manual of your NAD Receiver or Tuner for control button compatibility. auto tune: In DAB mode, press this button to automatically scan all available local stations. [. . . ]