User manual NAIM CDX2

[. . . ] WORLD CLASS HI FI OWNERS MANUAL CD Players: CDS3, CDX2, CD5x, CD5i IMPORTANT In order to comply with current European safety regulations it is essential that the Naim loudspeaker connectors supplied with amplifiers and loudspeakers are used. Do not under any circumstances allow anyone to modify your Naim equipment without first checking with the factory, your dealer, or your distributor. For your own safety do not under any circumstances open Naim equipment without first disconnecting it from the mains. Warning: an apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing connection. [. . . ] The optional RS232 interface can provide external control of the player in special custom installations. Contact your dealer or Naim Audio directly for further information. CDX2 DIN Output nc nc ch1 ch2 -ve 8 CDX2 9. 2 CDX2 Connected to XPS Power Supply mains input and fuse Note When used with an XPS the CDX2 must be disconnected from the mains. Always switch off the CDX2 when connecting or disconnecting an XPS. cable direction marker Interconnect Cables CDX2/XPS Burndy 9 CD5x 10 Installation and Operation The CD5x CD Player can be operated either from its internal power supply or, for improved performance, from an external Naim Flatcap 2 or Hi-Cap Power Supply. Connection of the power supply is illustrated in Diagram 11. 2 The CD5x should be installed on a dedicated equipment stand intended for the purpose. To improve sound quality the player has hard metallic feet which may blemish any delicate surface on which it is placed. Do not stand the player directly on top of another item of Naim Audio equipment. A transit screw on the underside of the CD5x case should be removed before use and must be replaced if the unit is to be re-packed and shipped. Do not invert the player once the transit screw is removed. 10. 1 Disc Loading Disc loading is illustrated in Diagram 14. 2. To load a compact disc pull open the CD drawer using the handle on the left hand side of the player. The illustration in Section 15 will help identify the correct puck for the CD5x. If an HDCD® encoded compact disc is loaded the CD5x will automatically recognise and decode it. The display will read HDCD for a few seconds after play is pressed. 10. 3 Front Panel Control Modes The CD5x has an optional front panel control mode. This multifunction mode provides an alternative front panel interface in which fast forward, fast reverse and pause are selected by pressing and holding next, previous and play respectively. To select multi function mode press and hold next while the player is switched on. To select the standard control mode press and hold previous while the player is switched on. 10. 4 Player Display and Indicators The alphanumeric display indicates track and index numbers, time in minutes and seconds, or various system messages (Error, Track programming info, etc). The full stop on the right of the display window illuminates when the player receives a signal from the remote handset. If a track play list is programmed the time displayed reflects the duration of the program. HDCD: time: repeat: prog: Illuminates to show that an HDCD encoded disc is playing. Illuminates to indicate display of total disc time or elapsed time of the track being played. Illuminates to show that repeat has been selected from the remote handset. Further information on play list programming can be found in Sections 16, 17 and 18. 10. 2 Player Controls previous: With a disc loaded but not playing the previous button searches the disc contents backwards, either one track at a time, or sequentially if the button is held. While a disc is in play, the previous button searches the table of contents backwards. [. . . ] The tuner display will indicate stereo when both stereo operation is selected and a stereo signal is received. The mono button on the tuner will illuminate when mono is selected. up & down mono 18. 4 Soft Keys These keys operate functions depending on the System Component Key setting. numeric keys: In preamp mode the numeric keys will switch between the preamplifier inputs. In tuner mode the numeric keys will select tuner presets or tuner frequency. [. . . ]