User manual NIKON LS-2000

[. . . ] 35 mm Film Scanner LS-2000 User's Guide Cautions · The reproduction of this manual in whole or in part is prohibited save in cases in which Nikon's prior permission has been obtained. The information contained in this manual is subject to change without notice. Nikon has made every effort to produce a perfect manual, but should you find any mistakes, we would be grateful if you would kindly let us know. The address of Nikon's representative in your area is provided separately. [. . . ] How the scanner should be connected to the chain depends on whether it is to be located between other devices or attached at the end of the chain. 10 Nikon LS-2000 35 mm Film Scanner User's Guide 3. Set the terminator switch on the rear of the scanner to ON TERMINATOR OFF ON 2. Connect the SCSI cable to either of the two SCSI connectors on the rear of the scanner and connect the other end to the next device in the chain Scanner only external device in chain 100­240V~ 0. 3­0. 2A 50/60 Hz 100098 MADE IN JAPAN SCSI NB 4 5 67 23 TERMINATOR 1 OFF SCSI ON SCSI Other SCSI device Other SCSI device 23 1 SCSI Nikon LS-2000 35 mm Film Scanner User's Guide 0 0 Scanner last of several external devices 100­240V~ 0. 3­0. 2A 50/60 Hz 100098 MADE IN JAPAN SCSI NB 4 5 TERMINATOR 67 OFF SCSI ON 11 3. Set the terminator switch on the rear of the scanner to OFF TERMINATOR OFF ON 2. Connect the SCSI cable from one of the devices in the chain to either of the connectors on the rear of the scanner, then connect a cable to the remaining connector and attach the other end to a connector on the next device in the chain 100­240V~ 0. 3­0. 2A 50/60 Hz 100098 MADE IN JAPAN SCSI NB 4 TERMINATOR Other SCSI device OFF SCSI ON 5 67 0 SCSI 1 23 Terminator 3. Confirm that the last device in the chain is terminated Note: If the last device in the chain has an unused SCSI connector, a separate terminator should be attached to it, even if the device is connected to the SCSI chain using a through terminator. 12 Nikon LS-2000 35 mm Film Scanner User's Guide 3. Setup SCSI connection checklist · Turn off the computer, the LS-2000, and all SCSI devices before connecting the scanner. · Be sure that the devices at both ends of the SCSI chain are terminated. If the host computer is a Macintosh, the chain will already be terminated at the computer end. In the case of IBM PC/AT compatibles in a chain which contains external devices only, the chain should be terminated at the SCSI board. In the case of a chain which includes internal devices, you may need to remove termination from the board and terminate the last internal device. The maximum number of SCSI devices that can be connected in a single chain is eight, including the computer and any internal SCSI devices such as hard disks or CD-ROM drives. The total length of cabling in the SCSI chain should be no more than six meters (twenty feet). The longer the cabling, the less reliable the connection. · · Safety Precautions · Do not damage the SCSI cabling's protective insulation. Do not forcibly tug or bend SCSI cables, place cables under heavy objects or expose them to heat or flame. When disconnecting cables, handle the cable by the connector, not by the cable itself. Should the insulation be damaged or the internal wiring exposed, replace the cable immediately. Do not handle SCSI cables or devices when your hands are wet. · Nikon LS-2000 35 mm Film Scanner User's Guide 13 3. Setup Step 5--Set the scanner's SCSI ID Each device in the SCSI chain has a unique ID, which is a number between zero and seven that the computer uses to distinguish between different devices. When connecting the LS-2000 to a SCSI chain, the scanner's SCSI ID must be set to a number that is not shared by any of the other devices, including the computer itself. The scanner's SCSI ID is indicated by the SCSI ID dial on the rear panel. Before the scanner leaves the factory, the ID is set to "2. " SCSI ID 4 5 23 67 0 When choosing another ID for the scanner, bear in mind that the computer will usually have an ID of either "0" or "7, " and that internal hard disks often have IDs of "0" or "1. " In the case of Macintosh computers, the computer will have an ID of "7, " while the internal hard disk and CD-ROM drive often have IDs of "0" and "3, " respectively. [. . . ] The effects of Defect Correction will be visible in the preview image in the scan window. Consult the software reference manual for your platform for more information on the scanner extras available for the LS-2000, including multi-sample scanning. Step 12--Adjust color balance, contrast, and brightness The controls in the color-balance drawer can be used to adjust RGB color balance, contrast, and brightness. Click the color-balance drawer-tab to open the color-balance drawer. Adjust brightness, contrast, and color balance by dragging the sliders. [. . . ]