Detailed instructions for use are in the User's Guide.
[. . . ] MODEL
d-Copia 16W d-Copia 20W
DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL · BEFORE USING THE MACHINE · COPY FUNCTIONS · PRINTER FUNCTIONS · USER SETTINGS
Page
8 18 29 31
· TROUBLESHOOTING 40 · ROUTINE MAINTENANCE 55
d-Copia 16W
· PERIPHERAL DEVICES AND SUPPLIES · APPENDIX
58 60
d-Copia 20W
PUBLICATION ISSUED BY: Olivetti S. p. A. Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright © 2005, Olivetti All rights reserved
May 2005
The mark affixed to the product certifies that the product satisfies the basic quality requirements.
The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice.
ENERGY STAR is a U. S. registered mark.
The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment.
Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · incorrect electrical power supply; · incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; · replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel.
All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher.
Do not make copies of anything which is prohibited from copying by law. [. . . ] When the indicator is blinking, a print job is transferred to the machine.
5
Click the "Print" button or the "OK" button to begin printing.
The print job will be delivered to the paper output tray.
Important points when setting the paper size
· Make sure that the tray's paper size setting is the same as the tray's paper size setting in the printer driver. For example, if the tray's paper size setting is A4R (8-1/2" x 11"R), set "Setting Paper Size" to "A4-R" ("Letter-R"). For more information, see "CONFIGURING THE PRINTER DRIVER" in the "Software Setup Guide".
29
PRINTER FUNCTIONS
Pausing a print job
To pause a print job during printing, press the [ON LINE] key ( ) on the operation panel to switch the machine off-line. To cancel a print job, press the [CLEAR] key ( ) or the [CLEAR ALL] key ( ). To resume printing, press the [ON LINE] key ( ) to switch the machine online.
When "Use close paper size" is disabled
The PAPER SIZE indicator on the operation panel will blink. You can press the [TRAY SELECT] key ( tray manually, or load paper in the bypass tray and press the [ON LINE] key ( ) to begin printing. ) to select a
When "Use close paper size" is enabled
Printing will take place using a size of paper that is close to the size of the print image.
OPERATION IN COPY AND PRINTER MODES
Some operations cannot be performed simultaneously when the machine is being used in printer mode or copy mode. Modes Copy Printer Copy key input During copying During printing Copying Yes Yes*1 Yes*3 Printing Yes No*2 No
*1 Can be used after pressing the [INTERRUPT] key ( ). ) is pressed after the copy job is finished, or when the [ON LINE] key ( ) is *2 Printing will begin when the [CLEAR ALL] key ( pressed to switch the machine online. Printing will also begin after the set auto clear time elapses, or after 60 seconds if "Auto clear time" is disabled. *3 The print job is paused and copying begins.
30
4
Note
Chapter 4
USER SETTINGS
This chapter explains how to set the automatic exposure level, toner save mode/high image quality mode, and the user programs, which are custom settings that control fine points of the machine's operation.
ADJUSTING THE AUTOMATIC EXPOSURE LEVEL
The exposure level used in automatic exposure adjustment, which automatically adjusts the copy exposure according to the original, can be adjusted. If copies tend to be too dark or too light when automatic exposure adjustment is used, follow the steps below to adjust the automatic exposure level. The automatic exposure level can be adjusted separately for the document glass and the SPF.
The copy and printer cannot be used while the automatic exposure level is being adjusted.
1
To adjust the automatic exposure level in the SPF, place the original in the SPF. (p. 19)
Make sure that the SPF indicator is lit.
To adjust the automatic exposure level for copies made from originals placed on the document glass, proceed to step 2.
4
Press the [Light] key ( ) or [Dark] key ( ) to lighten or darken the automatic exposure level as desired.
135
Note
2 3
Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to select "PHOTO" ( ). Hold down the [AUTO/TEXT/PHOTO] key ( AUTO / / ) until the AUTO indicator ( AUTO ) blinks.
AUTO
5
Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to complete the setting.
The AUTO indicator ( AUTO ) stops blinking and lights steadily.
135
The exposure level indicators show the current setting.
Note
After adjusting the automatic exposure level, it is recommended that you make a test copy to check the new level.
31
TONER SAVE MODE AND HIGH IMAGE QUALITY MODE
Toner save mode can be enabled to reduce toner consumption by about 10%. The high image quality mode improves copy image quality in the automatic and manual exposure modes by increasing copy density with a slight increase of toner consumption. To switch between toner save mode and high image quality mode, follow the steps below.
Note
In Europe, high image quality mode is initially selected. In regions other than Europe, toner save mode is initially selected.
1
Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to select "TEXT" ( ). Hold down the [AUTO/TEXT/PHOTO] key ( AUTO / / ) until the PHOTO indicator ( ) blinks.
AUTO
2
135
The exposure level indicators show the current setting.
3
To enable toner save mode, press the [Light] key ( ). To enable high image quality mode, press the [Dark] key ( ).
135
When enabling toner save mode, make sure that "1" is lit. When enabling high image quality mode, make sure that "5" is lit.
4
Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to complete the setting.
The PHOTO indicator ( lights steadily. ) stops blinking and
32
CUSTOMISING SETTINGS
(User programs)
The user programs allow you to customise the machine to match your needs.
USER PROGRAMS
Program number Program name Setting codes (factory default setting appears in bold) 1: OFF 2: 10 sec. [. . . ] 31 Using the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 24 XY-ZOOM key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 24 Z ZOOM indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 23, 24
65
INDEX BY PURPOSE Copying Automatic ratio selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Cancelling a copy run. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 19 Copying, starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 19 Dual page copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]