User manual ONE FOR ALL SV-9380

[. . . ] - In order to avoid having to re-program your ONE FOR ALL 4 after you remove the batteries, you will need to insert new batteries within 5 minutes. - On the inside of the battery compartment door you will find a label on which to write your Set-Up Codes for future reference. This you will do after setting up your ONE FOR ALL 4 remote for your devices. The Keypad Please refer to the picture of the ONE FOR ALL 4 Remote Control on Page 3. 1 2 3 4 Magic Key: The Magic key is used to set-up your ONE FOR ALL 4 Remote Control and to access special functions. Power Key: The Power key controls the same function as it did on your original remote. [. . . ] Mute Key: The Mute key operates the same function it did on your original remote. Volume Up / Down Control: These keys operate just as those on your original remote. Directional Keys If available on your original remote, these keys will allow you to navigate through the menu of your device. 5 6 7 8 9 10 WWW. ONEFORALL. COM 4 The Keypad 11 OK key If your original remote control required that you press an "OK" or "ENTER" key during Menu operation, this key can be used for this function. Menu Key: Controls the same function as it did on your original remote control. 12 13 14 Exit Key: The Exit key will exit the Menu. EPG key If available on your original remote, this key will provide the "Electronic Program Guide" (EPG) function. In TV mode this key allows you to access the wide screen (16:9) view option of your television (if available on your original remote). VCR / DVD keys (PLAY, STOP, REW etc. ) After pressing the VCR mode key, the Playback keys operate the same functions of your Video Recorder Keys. To prevent accidental recording, the RECORD key must be pressed twice. After pressing the DVD mode key, the Playback keys will operate the same functions of your DVD Players. In VCR mode the SP/LP key controls the tape speed function, the AUTO key controls the auto tracking function, just like on your original remote. Teletext Functions: After pressing the TV key, the transport keys (REW, PLAY, FF, PAUSE) are used to operate the main Teletext functions. Press and hold down MAGIC until the ONE FOR ALL 4 red light blinks twice (the red light will blink once then twice). Now press CH+ over and over, until your Television turns off (every time you press the CH+ key the ONE FOR ALL 4 will send out a POWER signal from the next code contained in the memory). You may have to press this key many times (up to 150 times) so please be patient. If you skip past a code, you can go to the previous code(s) by pressing the CH- key. Remember to keep pointing the ONE FOR ALL 4 at your Television while pressing this key. 4. 6. CH 7. As soon as your television turns off, press MAGIC to store the code. - Most TV's do not switch on pressing the POWER key. Please try pressing a "number" key or the "TV-text off" key to switch your TV back on. - If you cannot control your Television properly, please continue the Search Method, you may be using the wrong Code. - To search for the code for another device follow the instructions above only press the appropriate device key instead of TV during step 2. - If the original remote control of your Video recorder or DVD player does not have a POWER key, press PLAY instead of POWER during step 5. WWW. ONEFORALL. COM 7 Code blink out (To find out which code is currently programmed) Once you have Set-Up your ONE FOR ALL 4, you can blink back your Set-up Code for future reference. Press and hold down MAGIC until the ONE FOR ALL 4 red light blinks twice (the red light will blink once then twice). [. . . ] This is useful if you want to set up two of the same devices on the ONE FOR ALL 4. Example Example Example 1 if you like to program a second TV on the DVD key. 3 if you like to program a second VCR on the SAT key. Example 1: To program a second Television on the DVD key (for example), you need to change the DVD key into a TV key, so press: (*) The DVD key has now become a second TV key. Now enter the Set-Up code for your second TV by pressing: (*) Example 2: To program a second Television on the SAT key (for example), you need to change the SAT key into a TV key, so press: (*) The SAT key has now become a second TV key. [. . . ]