User manual ONE FOR ALL URC 3021

[. . . ] For master power control, see Programming A Master Power Macro on page 10. Use the keypad (1 ~ 9 and 0) to directly select channels (e. g. , 009 or 031). Use TV/VID to switch the TV's input to view TV or video programs. Use GUIDE to display your selected device's program guide or setup menu. Use INFO to display the current channel and program or on-screen directory. [. . . ] This allows you to still individually power devices on or off. 2. Devices will turn on (or off) according to your programmed sequence. NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s). continued on next page. . . 10 CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 11 PROGRAMMING A MASTER POWER MACRO (cont'd) Clearing The Master Power Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Then press POWER once. 3. Press and hold SET until the LED blinks twice, then release SET. The Master Power Macro is now cleared. RE-ASSIGNING DEVICE KEYS The One For All 3 Device Universal Remote Control can be set to control a DVD player and a VCR (or a PVR) or a second DVD player by re-assigning the unused CBL/SAT key as follows: 1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. Press CBL/SAT once. The LED will blink twice. The CBL/SAT key is now ready to be set up to control your VCR (or PVR) or second DVD player. See Programming Device Control on page 8. NOTE: Only one device can be assigned to an unused device key at a time. USING CHANNEL SCAN In the CBL/SAT or TV mode, use the FAV key to start a 3-second scan of all channels. Or, if programmed, use the FAV key to scan only your favorite channels to view a desired channel (see Programming Favorite Channel Scan on next page. Press CBL/SAT or TV once. 2. Press FAV once. · If Favorite Channel Scan has been set up, scanning of favorite channels will start with up to 100 channel changes or until stopped by pressing any key. · If Favorite Channel Scan has not been set up, scanning will start with the current channel, and continue up to 100 channel changes or until stopped by pressing any key. 3. To stop scanning channels at any time, press any key once. 11 CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 12 PROGRAMMING FAVORITE CHANNEL SCAN In the CBL/SAT or TV mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when FAV is pressed (see Using Channel Scan on the previous page). NOTE: Favorite channels can only be programmed for one mode. After programming, if FAV is pressed while in another mode, the remote control will start scanning all channels instead (if applicable to the selected device). 1. On the remote control, press CBL/SAT or TV once. 2. 3. Press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. 4. Use the keypad to enter a favorite channel number (e. g. , 031). Then press SET once. NOTE: If the original remote control required pressing an Enter key to change the channel, also press the ENTER key after the channel number (e. g. , 0 - 3 - 1 - ENTER). On some satellite receivers and cable boxes, you may need to press the SELECT (OK) key instead of ENTER. 5. If desired, repeat step 4 for each channel to be stored, up to a total of 10 channels. NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming. To change your favorite channel list at this point, you will first need to delete the existing list by performing the steps in "Clearing Custom Programming" on page 14. Then, perform the instructions in this section once again. 6. To exit programming with less than 10 favorite channels stored, press and hold SET until the LED blinks twice. Otherwise, the remote control will automatically exit the program after 10 channels have been stored. CHANGING VOLUME LOCK The One For All 3 Device Universal Remote Control is set at the factory for independent volume control of each selected device. However, you may change the Volume Lock setting to Global Volume Lock so that a device's volume will be locked to one mode (e. g. , to control TV volume in all other modes). After that, if desired, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation. Locking Volume Control To One Mode (Global Volume Lock) 1. Press and hold SET until the LED (red light) blinks twice, then release SET. continued on next page. . . 12 CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 13 CHANGING VOLUME LOCK (cont'd) Locking Volume Control To One Mode (Global Volume Lock) 2. [. . . ] 8918 Stone Green Way, Louisville, KY 40220 together with the original receipt and $3. 95 to cover postage and handling. The manufacturer reserves the right to substitute a currently manufactured model with equal or superior features. One For All: (330) 405-8655 URC-3021 March 2004 16 CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 17 ADDITIONAL INFORMATION As you update your home entertainment system, One For All® has a universal remote control that will fit your needs. Look for these exciting products at a retailer near you: One For All Access 3. [. . . ]