User manual ONKYO A-905TX

[. . . ] English Integrated Stereo Amplifier Before using A-905TX Connections Preparations Instruction Manual INTEGRATED STEREO AMPLIFIER VOLUME WIDE RANGE AMP TECHNOLOGY INPUT Operation STANDBY/ON CD MD TUNER TAPE LINE/ DVD STANDBY CDR/PC DIRECT BASS POWER PHONES TREBLE BALANCE SOURCE DIRECT DIRECT TONE ACOUSTIC PRESENCE ON OFF -- + -- + L R OFF / 1 / 2 A-905TX Other Information Before using Thank you for purchasing . . . Thank you for purchasing the ONKYO A-905TX Integrated Stereo Amplifier. Please read this manual thoroughly before making any connection or turning on the power. Follow these instructions to obtain optimum performance and maximum listening enjoyment from your new A-905TX. Please retain this manual for future reference. Main Features · · · · High-Quality Separate Component WRAT (Wide Range Amp Technology) Circuit Processor In/Out, Subwoofer Pre Out Six-audio Source Inputs · Acoustic Presence Circuit Naturally Enhances the Extreme Low Range · Source Direct Function · System Control Remote Controller Memory Preservation This unit does not require memory preservation batteries. [. . . ] · Program Timer You can operate timer playback and recording using T-405TX. · On each pair of connectors, a red connector (marked R) corresponds to the right channel, and a white connector (marked L) to the left channel. Connect white plugs of audio connection cables to L connectors and connect red plugs of audio connection cables to R connectors. · Please refer to the instruction manual for each component when you make any connections. Audio connection cable To L connector To R connector (White) (Red) (White) (Red) To L connector To R connector · Insert the plug securely. If the connection is incomplete, noise or malfunction may result. Improper connection Insert completely · When you use a digital audio optical cable, do not bend it sharply nor coil it tightly. · Bundling an audio connection cable with the power cord or speaker cord may degrade the sound quality. · Be sure to use the cable, supplied with each component (except for the A-905TX) to connect to the remote control connector. If the connection is incomplete, you will be unable to operate the device using the remote controller. To connect both the MD recorder MD-105TX and stereo cassette tape deck K-505TX to the unit: Connect the MD recorder to the unit following the "Connections for combination example 2" on the next page and connect the stereo cassette tape deck to the unit following the "Connections for combination example 1. " The 230-240 V model is shown in the following illustrations. 8 Connections for combination example 1 OUT(REC) IN(PLAY) OUTPUT OUTPUT REMOTE CONTROL L L AC OUTLET AC 230-240V UNSWITCHED 100W MAX. 50Hz L OUT(REC) IN(PLAY) L CAUTION: SPEAKERS L L SPEAKER IMPEDANCE 4 OHMS MIN. /SPEAKER R R TUNER LINE/DVD OUT(REC) IN(PLAY) TAPE REMOTE CONTROL OUT(REC) IN(PLAY) R L L ANTENNA FM 75 R R R AC OUTLET R AC 230-240V CDR/PC CD MD OUT PROCESSOR IN SUBWOOFER PRE OUT 50Hz SWITCHED 100W MAX. TUNER LINE/DVD R TAPE OUT(REC) IN(PLAY) Before using Tuner (T-405TX) OUT(REC) IN(PLAY) L Amplifier ­ this unit (A-905TX) R CDR/PC CD MD Connections ANALOG OUTPUT L ANALOG OUTPUT L AC OUTLET AC 230-240V UNSWITCHED 100W MAX. REMOTE CONTROL INPUT OUTPUT 50Hz (REC) (PLAY) INPUT OUTPUT (REC) (PLAY) R DIGITAL OUTPUT 1 OPTICAL 2 "CLASS 1 LASER PRODUCT" L D REMOTE CONTROL L D R AC OUTLET AC 230-240 V 50 Hz UNSWITCHED 100W MAX. R R CD player (C-705TX) or CD changer (C-707CHX) : Signal flow Stereo cassette tape deck (K-505TX) Preparations Connections for combination example 2 OUT(REC) IN (PLAY) L L Tuner (T-405TX) OUTPUT OUTPUT REMOTE CONTROL R R TUNER LINE/DVD OUT(REC) IN (PLAY) TAPE OUT(REC) IN (PLAY) Amplifier ­ this unit (A-905TX) OUT(REC) IN (PLAY) L CAUTION: SPEAKERS L AC OUTLET AC 230-240V UNSWITCHED 100W MAX. 50Hz L L L SPEAKER IMPEDANCE 4 OHMS MIN. /SPEAKER Operation R R L ANTENNA FM 75 R L TUNER LINE/DVD OUT(REC) IN (PLAY) TAPE REMOTE CONTROL OUT(REC) IN (PLAY) R R AC OUTLET R AC 230-240V CDR/PC CD MD OUT PROCESSOR IN SUBWOOFER PRE OUT 50Hz SWITCHED 100W MAX. R CDR/PC CD MD Other Information ANALOG OUTPUT L DIGITAL OUTPUT 1 OPTICAL ANALOG INPUT (REC) OUTPUT (PLAY) DIGITAL INPUT OPTICAL 2 L L 1 2 R R R ANALOG OUTPUT L AC OUTLET AC 230-240V UNSWITCHED 100W MAX. REMOTE CONTROL 50Hz ANALOG INPUT (REC) OUTPUT (PLAY) REMOTE CONTROL R DIGITAL OUTPUT 1 OPTICAL DIGITAL INPUT OPTICAL 1 2 2 "CLASS 1 LASER PRODUCT" L L R R CD player (C-705TX) : Signal flow Optical cable MD recorder (MD-105TX) 9 Connecting to the ONKYO Separate Collection Series components Connecting a CD Recorder CDR-205TX: ANALOG INPUT (REC) OUTPUT (PLAY) REMOTE CONTROL L INPUT 1 OUT(REC) IN(PLAY) OUT(REC) IN (PLAY) L CAUTION: SPEAKERS DIGITAL OPTICAL L OUTPUT L ANALOG INPUT (REC) OUTPUT (PLAY) L L SPEAKER IMPEDANCE 4 OHMS MIN. /SPEAKER L INPUT 2 R REMOTE CONTROL L INPUT 1 R TUNER LINE/DVD DIGITAL OPTICAL OUT(REC) IN(PLAY) OUTPUT REMOTE TAPE CONTROL OUT(REC) IN(PLAY) R INPUT 2 L AC OUTLET R R R K L R R R AC 230-240V CDR/PC CD MD OUT PROCESSOR IN SUBWOOFER PRE OUT 50Hz SWITCHED 100W MAX. CD Recorder (CDR-205TX) CDR/PC CD Amplifier ­ this unit (A-905TX) : Signal flow Connecting a processor such as ED-205: OUT(REC) IN(PLAY) L CAUTION: SPEAKERS VIDEO S VIDEO SUB WOOFER PRE OUT REMOTE CONTROL SURROUND L L L SPEAKER IMPEDANCE 4 OHMS MIN. /SPEAKER CENTER IN VIDEO-1 OUT IN VIDEO-2 IN MONITOR VIDEO-1 OUT OUT IN VIDEO-2 MONITOR OUT CENTER R R R TUNER LINE/DVD OUT(REC) IN(PLAY) REMOTE TAPE CONTROL OUT(REC) IN(PLAY) R L CAUTION: SPEAKER IN VIDEO-1 OUT IN VIDEO-2 IN OUT PROCESSOR FRONT SURROUND IMPEDANCE 6 OHMS MIN. SUB/SPEAKER WOOFER MULTI CHANNEL INPUT SPEAKERS L AC OUTLET R R AC 230-240V CDR/PC CD MD OUT PROCESSOR IN SUBWOOFER PRE OUT 50Hz SWITCHED 100W MAX. IN OUT PROCESSOR FRONT OUT PROCESSOR IN SUBWOOFER PRE OUT Processor (e. g. ED-205) Amplifier ­ this unit (A-905TX) : Signal flow Note: Jumper plugs have been installed on the A-905TX's PROCESSOR connectors. To connect an AV surround processor, such as ED-205, remove the jumper plugs, then connect pin cables (see page 13). 10 Connecting the connectors and AC OUTLETS Before connecting · The hookups on page 9, 10 is needed in addition to the (for remote control operations) and AC OUTLET (for power supply to each component) hookups on this page. · The cable for connecting the connectors is supplied with each component (not supplied with the unit). Before using Connections To use the Clock/Timer function of the tuner T-405TX's, connect the power cord as shown below and connect the cable and audio connection cables (see page 9, 10). Be sure to connect the power cord of the T-405TX to an AC outlet that supplies continuous power. Also, turn on the POWER switch on the A-905TX to use the Timer function. Stereo cassette tape deck (K-505TX) or MD recorder (MD105TX) (The illustration is MD-105TX. ) OUTPUT Connections To wall outlet REMOTE CONTROL INPUT OUTPUT (REC) (PLAY) REMOTE CONTROL L AC OUTLET AC 230-240V UNSWITCHED 100W MAX. 50Hz L D R AC OUTLET AC 230-240 V 50 Hz UNSWITCHED 100W MAX. ANTENNA FM 75 R Tuner (T-405TX) Preparations ANALOG OUTPUT OUT(REC) IN(PLAY) L CAUTION: SPEAKER IMPEDANCE 4 OHMS MIN. /SPEAKER CD player (C-705TX) or CD changer (C707CHX) L L L AC OUTLET AC 230-240V UNSWITCHED 100W MAX. REMOTE CONTROL 50Hz SPEAKERS R R R DIGITAL OUTPUT 1 OPTICAL TUNER LINE/DVD OUT(REC) IN(PLAY) TAPE 2 REMOTE CONTROL OUT(REC) IN(PLAY) R "CLASS 1 LASER PRODUCT" L AC OUTLET R AC 230-240V CDR/PC CD MD OUT PROCESSOR IN SUBWOOFER PRE OUT 50Hz SWITCHED 100W MAX. Amplifier ­ this unit (A-905TX) Note: If you have a CD Recorder CDR-205TX, connect the CDR-205TX's connector on the A-905TX. Operation connector to an available If you connect the power cord as shown below, you can turn off the power to the entire system by simply turning off the POWER switch on the amplifier A-905TX. Note: If the system is connected so that you can use the tuner's T-405TX Clock/Timer function, turning off the power to the entire system will turn off the power to the tuner, and the Clock and Timer functions will no longer function. If you wish to use the clock or Timer function, leave the POWER switch set to ON. K-505TX or MD-105TX INPUT OUTPUT (REC) (PLAY) T-405TX Other Information OUTPUT REMOTE CONTROL REMOTE CONTROL L AC OUTLET AC 230-240V UNSWITCHED 100W MAX. 50Hz L D R AC OUTLET AC 230-240 V 50 Hz UNSWITCHED 100W MAX. ANTENNA FM 75 R C-705TX or C-707CHX ANALOG OUTPUT L AC OUTLET AC 230-240V UNSWITCHED 100W MAX. 50Hz A-905TX OUT(REC) IN(PLAY) L CAUTION: SPEAKERS L L SPEAKER IMPEDANCE 4 OHMS MIN. /SPEAKER R R R REMOTE CONTROL DIGITAL OUTPUT 1 OPTICAL TUNER LINE/DVD OUT(REC) IN(PLAY) 2 REMOTE TAPE CONTROL OUT(REC) IN(PLAY) R "CLASS 1 LASER PRODUCT" To wall outlet AC OUTLET AC 230-240V 50Hz SWITCHED 100W MAX. L R CDR/PC CD MD OUT PROCESSOR IN SUBWOOFER PRE OUT 11 Connecting to components other than the Separate Collection Series Connecting audio/video equipment to audio connectors Before connecting · Do not connect the AC power cord (mains lead) to the wall outlet (the mains) until you have completed all the other connections including the sound processor connections on the next page, the connections on page 14, and the speaker connections on page 15. · On each pair of connectors, a red connector (marked R) corresponds to the right channel, and a white connector (marked L) to the left channel. Connect white plugs of audio connection cables to L connectors and connect red plugs of audio connection cables to R connectors . Audio connection cable To L connector To R connector (White) (Red) (White) (Red) To L connector To R connector · Please refer to the instruction manual for each component when you make any connections. [. . . ] Insert the CD you want to record from into the CD player. 1 Turn INPUT selector clockwise or counterclockwise until the input indicator of the source you wish to record from lights. Or press INPUT button on the remote controller. INPUT ONKYO CD PLAYER CD PLAYER INPUT 3 Prepare the recording component. e. g. 1 Insert an MD into the MD recorder. or The indicators light in the following order: CD MD TUNER e. g. 2 Insert a cassette into the stereo cassette tape deck. CDR/PC LINE/DVD TAPE When you press the INPUT button on the remote controller repeatedly, the indicators light up in clockwise order. [. . . ]