User manual ONKYO A-9377

[. . . ] Integrated Amplifier Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 A-9377 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making any connections or plugging in your new Onkyo product. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Onkyo product. [. . . ] 18 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note: · Do not connect a source component to the PREOUT jacks. E AC OUTLETS Supply AC power to other audio components. The type of connector depends on the destination country. F PHONO (MM) Analog audio input for connecting a turntable with a moving-magnet cartridge. M G CD Analog audio input for connecting a CD player. H TUNER Analog audio input is for connecting a tuner. REMOTE CONTROL (Remote Interactive) jacks can be connected to jacks on other Onkyo audio components so that you can control them with the A-9377's remote controller. To use , you must also make an analog audio connection between the A-9377 and each component. If your A-9377 has a VOLTAGE selector, set it to match the AC voltage used in your area before plugging in the power cord. (See page 3. ) I TAPE IN/OUT Analog audio input and output for connecting a cassette deck. N VOLTAGE SELECTOR (not European model) See pages 11­14 for connection information. 7 Introduction--Continued Remote Controller In the illustration below, numbers in circles indicate buttons that can be used to control the A-9377. Numbers in squares indicate buttons that can be used to control other Onkyo audio components connected to the A-9377 via . These buttons are explained on the next page. Buttons for Controlling the A-9377 The following buttons control the A-9377: D VOLUME [ ]/[ ] (16) Adjusts the volume of the A-9377. O INPUT [ ]/[ ] (16) Selects the input source: LINE, DOCK, PHONO, CD, TUNER, or TAPE. Q MUTING (16) Mutes the A-9377. 0 A 1 B C D 2 3 4 Q 5 6 7 8 9 H I O F 8 Introduction--Continued Buttons for Controlling Other Onkyo Components When other Onkyo audio components are connected to the A-9377 via , you can control them with the A-9377's remote controller. For example, when the DOCK input source is selected, the [RANDOM] button will operate an RI Dock/iPod's Shuffle function. But when the TAPE input source is selected, it will operate a cassette deck's Dolby NR function. The following table lists the function of the remote controller's buttons for each input source. Refer to each component's instruction manual for complete operating instructions. Input source Remote controller button CD [1]. . . [9] DOCK (RI Dock) CD (CD player) [1]. . . [9] [>10] [10/0] [BAND] [FM MODE] PRESET [+]/[­] ] [DIMMER] Pause [ Play [ Pause [ ] Rew/FF [ ] ] ]/[ ] ] Pause [ Play [ Stop [ Rew/FF [ ] ] ]/[ ] [DOLBY NR] [REV MODE] ] Reverse Play [ Play [ Stop [ ]*1 ]*1 ]*1 TUNING [ ]/[ ] TUNER (Tuner) TAPE (Cassette deck) 1 [>10] [10/0] [BAND] [FM MODE] PRESET [+]/[­] TUNING [ ]/[ ] ] ] ]/[ [DIMMER] Pause [ 2 3 5 6 7 8 Play [ Stop [ Rew/FF [ [RANDOM] [REPEAT] PLAYLIST [ ]/[ ]/[ ] ] [SHUFFLE] [REPEAT] PLAYLIST [ ALBUM [ ]/[ ]/[ ] ] [RANDOM] [REPEAT] 9 ALBUM [ MENU/SELECT [ ]/[ ] MENU/SELECT [ ]/[ ] [PLAY MODE] [SEARCH]*2 [MEMORY] [ENTER] [CLR] [BACKLIGHT] ] Prev/Next [ ]/[ ] [BACKLIGHT] [DISPLAY] [ Prev/Next ]/[ ] Rew/FF [ ]/[ ] 0 A B C D F H I [PLAY MODE] [GROUP/SEARCH] [MEMORY] [ENTER] [CLR] [DISPLAY] Prev/Next [ ]/[ [SCROLL] 1. For use with MP3 CDs. Note: · With some components, some buttons may not work as expected. Refer to the component's instruction manual for complete operating instructions. 9 Introduction--Continued Installing the Batteries Aiming the Remote Controller When using the remote controller, point it toward the A-9377's remote control sensor, as shown below. 1 To open the battery compartment, press the small hollow and slide open the cover. Remote control sensor 2 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. About 5 m (16 feet) 3 Slide the cover shut. Notes: · If the remote controller doesn't work reliably, try replacing the batteries. · Do not mix new and old batteries or different types of batteries. · If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion. · Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion. Notes: · The remote controller may not work reliably if the A-9377 is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. · If another remote controller of the same type is used in the same room, or the A-9377 is installed close to equipment that uses infrared rays, the remote controller may not work reliably. · Do not put anything on top of the remote controller, such as a book or magazine, because a button may be pressed continuously, thereby draining the batteries. [. . . ] Start playback on the source component. 2 3 Notes: · Signals output by the TAPE OUT L/R jacks are not affected by the A-9377's Volume, BALANCE, BASS, and TREBLE controls. · If you're using an Onkyo cassette deck that's connected via , for dubbing or synchro recording, set the REC SELECTOR to SOURCE. 17 Troubleshooting If you have any trouble using the A-9377, look for a solution here. If you cannot resolve the issue yourself, contact your Onkyo dealer. Remote Controller The remote controller doesn't work. Power Cannot turn on the A-9377. · Make sure that the power cord is properly plugged into the wall outlet. · Unplug the power cord from the wall outlet, wait ten seconds or more, then plug it in again. The SPEAKERS A and B indicators are both flashing. · The amp protection circuit has been activated. [. . . ]