User manual ONKYO A-RV400

[. . . ] Please retain this manual for future reference. Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . 19 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. [. . . ] The type of outlets depend on the country in which you purchased the A-9355/A-RV400. REMOTE CONTROL jacks The A-9355 has two jacks and the A-RV400 has one. These (Remote Interactive) jacks can be connected to the jacks on your other Onkyo audio components. The A-9355/A-RV400's remote controller can then be used to control all of your components. To use , you must make an analog audio connection between the A-9355/A-RV400 and each component. E Power Cord After finished all the required connections, plug the power cord into a wall socket. See pages 10­14 for connection information. F PHONO (MM) input This analog audio input is for connecting a turntable with a moving-magnet cartridge. 7 Remote Controller Remote Controller (Buttons to control the A-9355/A-RV400) 1 2 9 1 10 11 12 13 2 This section describes the function of the buttons to control the A-9355/A-RV400. A STANDBY button (14) This button is used to set the A-9355/A-RV400 to Standby. B ON button (14) This button is used to turn on the A-9355/A-RV400. C VOLUME [ ]/[ ] buttons (15) These buttons adjust the volume of the A-9355/A-RV400. 4 14 D INPUT [ ]/[ ] buttons (15) These buttons are used to select from the following input sources: LINE, HDD, PHONO, CD, TUNER, TAPE or MD. 3 E MUTING button (15) This button is used to mute the A-9355/A-RV400. 3 5 4 5 6 7 8 15 16 Remote Controller (Buttons to control Onkyo products other than A-9355/A-RV400) When other Onkyo audio components are connected to the A-9355/A-RV400 via , you can control them by using the corresponding buttons for each component listed in the following table. Example: For 6 - Random button · When the A-9355 has a MD player connected to the LINE/MD terminal, or a CD player to the CD terminal, the button functions as "RANDOM" control. · When the A-9355 has a RI dock connected to the DOCK terminal, or the A-RV400 has a RI dock connected to the LINE/DOCK terminal, the button functions as "SHUFFLE" control. · The button functions as "DOLBY NR" control, when a cassette deck is connected to the TAPE terminal. 8 Remote Controller--Continued DOCK (A-9355) LINE/DOCK (A-RV400) Connecting Terminal Component and (Input Name) Button on Remote Controller 1-9 1 10/0 >10 BAND 2 FM MODE PRESET +/­ TUNING 3 4 5 6 7 / DIMMER LINE/MD (A-9355) CD TUNER TAPE MD Recorder (MD) RI Dock (DOCK) CD Player (CD) Tuner (TUNER) Cassette Tape Deck (TAPE) 1-9 10/0 >10 1-9 10//0 >10 BAND FM MODE PRESET +/­ TUNING DIMMER * * * / / RANDOM REPEAT PLAYLIST / / / RANDOM REPEAT / SHUFFLE REPEAT PLAYLIST ALBUM / / / RANDOM REPEAT DOLBY NR REV MODE 8 ALBUM MENU/SELECT/ / 9 10 11 12 13 14 15 16 PLAY MODE GROUP/SEARCH MEMORY ENTER CLR DISPLAY / SCROLL PLAY MODE GROUP MEMORY ENTER CLR DISPLAY / SCROLL MENU/SELECT/ / PLAY MODE SEARCH (MP3 CD) MEMORY ENTER CLR BACKLIGHT / BACKLIGHT DISPLAY / / · Note also that some of the connected products may not be controlled with these buttons. For detailed information, refer to the relevant manuals provided for the individual products. · For detailed information on the function of individual buttons, see Instruction Manual of the listed components. · In the table above, blank cells indicate no function is available by pressing the button. * For a dual cassette deck, only the deck-B can be controlled. 9 Connecting the A-9355/A-RV400 Connecting Your Speakers Speaker Connection Precautions You can connect one or two sets of speakers (A/B) to the A-9355/A-RV400, and select which set outputs sound, or use both sets at the same time. For both speakers A and B, make sure to connect them with Left and Right in pairs. Connecting the Speaker Cables 1 Strip about 15 mm (5/8 inch) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown. If you connect other Onkyo components to the A-9355/A-RV400 with the appropriate and audio cables, you can use the following system functions. cables are special cables solely for use with Onkyo products (no cables are supplied with the A-9355/A-RV400). When you set the A-9355/A-RV400 to Standby, all connected components will go on Standby as well (the A-9355/A-RV400's POWER switch must be set to ON for this to work). Direct Change When playback is started on an audio component connected via , the A-9355/A-RV400 will automatically select that component as the input source. Remote Control Operation You can control all components in your system by using the A-9355/A-RV400's remote controller. · To use , you must make an analog audio connection between the A-9355/A-RV400 and each audio component. A-9355/A-RV400 Connecting Another Component's Power Cord The A-9355/A-RV400 has a switched AC OUTLETS on its rear panel. These can be used to connect the power cord of another audio component that you intend to use with the A-9355/A-RV400. After you power on the A-9355/A-RV400, you can feed or shut off power to the connected component by turning on or off the remote controller switch. Use the AC outlet of the A-9355/A-RV400 to feed only components that have no STANDBY/ON function, like Onkyo DX-7355 CD player. For Onkyo products equipped with terminals that have a STANDBY/ON function, allocate a normal outlet that is energized on a steady basis. Note: Do not connect any other devices than audio components. connector Onkyo CD player (DX-7355), etc. connector A-9355 Onkyo Tuner, etc. [. . . ] · The tone controls have no effect on the signal being recorded. 16 Troubleshooting If you have any trouble using the A-9355/A-RV400, look for a solution here. If you can't resolve the issue yourself, contact your Onkyo dealer. Power Can't turn on the A-9355/A-RV400. · Make sure that the power cord is properly plugged into the wall outlet. · Unplug the power cord from the wall outlet, wait ten seconds or more, then plug it in again. The STANDBY indicator is flashing. · The amp protection circuit has been activated. Remove the power cord from the wall outlet immediately and contact your Onkyo dealer. Turning on the system from Standby without using remote controller. · Begin by turning the POWER switch off ( ). [. . . ]