User manual ONKYO A-SV610PRO

[. . . ] Back cover page En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] · If another remote controller of the same type is used in the same room, or the A-SV610PRO/A-9555 is installed close to equipment that uses infrared rays, the remote controller may not work reliably. · Don't put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries. · The remote controller may not work reliably if the A-SV610PRO/A-9555 is installed in a rack behind colored glass doors. · The remote controller will not work if there's an obstacle between it and the A-SV610PRO/A-9555's remote control sensor. T MUTING button (15) This button is used to mute the A-SV610PRO/A-9555. U Previous and Next [ ]/[ ] buttons These buttons are used to select the previous or next track on a CD, MD, or HDD component. On a cassette deck, they're used for rewind and fast forward. V SCROLL button This button is used to scroll text displayed on an MD component. When the input source is "HDD, " this button turns on the display backlight on the HDD component. W MENU, SELECT, [ ]/[ ] buttons MENU button: Displays the HDD component menu. 9 Connecting the A-SV610PRO/A-9555 Connecting Your Speakers Speaker Connection Precautions You can connect one or two sets of speakers (A/B) to the A-SV610PRO/A-9555, and select which set outputs sound, or use both sets at the same time. For both speakers A and B, make sure to connect them with Left and Right in pairs. If you connect either Left or Right channel alone, no sound output will be available. If the electrical contact is poor for the connection, the Volume indicator will flash quickly when the power is supplied. Connecting the Speaker Cables 1 Strip about 15 mm (5/8 inch) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown. Unscrew the terminal. 15 mm (5/8") 2 3 · Connecting one set of speakers (A or B): Only connect speakers with an impedance of 4 ohms or more but less than 16 ohms. Auto Power On When you turn on the power or start playback on a component that's connected to the A-SV610PRO/A-9555, the A-SV610PRO/A-9555 will turn on automatically. And when you set the A-SV610PRO/A-9555 to Standby, all connected components will go on Standby as well (the A-SV610PRO/A-9555's POWER switch must be set to ON for this to work). Direct Change When playback is started on an audio component connected via , the A-SV610PRO/A-9555 will automatically select that component as the input source. Remote Control Operation You can control all components in your system by using the A-SV610PRO/A-9555's remote controller. See page 8 for more information. Remote Interactive Dock, etc. Remote control cable Notes: · Push each plug in all the way to make a good connection. · Use only dedicated cables for connections (no cables are supplied with the A-SV610PRO/A-9555). Connecting them to another manufacturer's component may cause the A-SV610PRO/A-9555 to malfunction. See the manuals supplied with your other Onkyo components for more information. · When using the A-SV610PRO as a power amplifier (MAIN IN function), the system functions are unavailable. 13 Enjoying Audio Sources Turning On the A-SV610PRO/A-9555 POWER STANDBY indicator STANDBY ON Note: To shut down the A-SV610PRO/A-9555 completely, set the [POWER] switch to the OFF position ( ). Selecting Speaker 1 A-SV610PRO/ A-9555 Press the [POWER] switch. The A-SV610PRO/A-9555 retains the power mode (on/standby) in which the amplifier was the last time you turned off the system. Notes: · The A-SV610PRO/A-9555 is shipped with the [POWER] switch in the OFF position ( ). [. . . ] · Make sure that the inputs and outputs of all components are connected properly. · Make sure that the polarity of the speaker cables is correct and that the bare wires are in contact with the metal part of each speaker terminal (page 10). · Make sure that the correct input source is selected (page 15). · If the Volume indicator flashes slowly, press the remote controller's [MUTING] button to unmute the A-SV610PRO/A-9555 (page 15). [. . . ]