User manual ONKYO DX-5500

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safeguards 1. Read Instructions ­ All the safety and operating instructions should be read before the appliance is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] · Using another remote controller of the same type in the same room or using the unit near equipment which uses infrared rays may cause operational interference. · Do not put any object such as a book on the remote controller. The buttons of the remote controller may be pressed by mistake and drain the batteries. Placing the unit behind such doors may prevent proper remote controller operation. · If there is any obstacle between the remote controller and the remote control sensor, the remote controller will not operate. System Connections · Do not plug in the power cord until all connections have been made. · On each pair of input or output jacks, the jack marked R corresponds to the right channel and the jack marked L corresponds to the left channel. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR COMPACT DISC PLAYER MODEL NO. DX-5500 OUTPUT REMOTE CONTROL DIGITAL OUTPUT OPTICAL L R Audio connection cable cable L CD To wall outlet Optical fiber cable (not included) R Optical IN Amplifier DAT, MD recorder or Digital amplifier Connecting to an audio system Two types of output jacks are located on the rear panel. Use the DIGITAL OUTPUT jack if you are connecting the unit to audio equipment that supports a digital connection. Connect these jacks to the amplifier's CD input jacks using the supplied audio connection cable. DIGITAL OUTPUT (optical) jack: For digital recording, connect this jack to the digital input jack of a Mini Disc recorder, a DAT deck, or other digital equipment. If your amplifier has a digital input jack, connecting the DIGITAL OUTPUT jack to it will produce a much clearer and more dynamic sound. Connections for remote controller ( ) · Terminal protection cap is attached to the digital jack. Remove the cap when connecting the unit to other digital equipment. Also, do not use conventional record cleaner or antistatic agents. 2 · Do not place a CD in direct sunlight or locations subject to · Do not store a CD in the CD changer tray for a long period high humidity or low temperature. of time. 8 Playing CDs DISPLAY PAUSE STOP / / Stopping playback temporarily PAUSE Press the PAUSE button. To resume playback, press PLAY button, or press the PAUSE button again. the The CD changer starts playing again from exactly the point at which it stopped. Stopping playback STOP Press the STOP button. · When you open the loading drawer, the disc that was playing will be in the front disc tray. Search play Hold down the / button to fast forward the current track during playback. Hold down the / button to fast reverse the current track during playback. / or / button when you reach the Release the point on the track you want to play back. You can also use the remote controller to search by using the and buttons instead of the / and / buttons. · The unit starts fast forwarding at 10-times speed, and after four seconds at 60-times speed. · During the fast forward operation, you will hear a cueing sound at low volume. · When the end of the disc is reached, the unit will play back the next disc. [. . . ] In this case, you do not need to press the MEMORY button. REMOTE CONTROLLER RC-331C 2 DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6 DISC 1 DISC 2 DISC 3 DISC 4 REMOTE CONTROLLER RC-331C DISC 5 DISC 6 · To store tracks on other discs into the memory, repeat steps · Repeat Step 3 to select a track from the same disc. · If you attempt to select more than 40 tracks, "FULL" will 2 and 3. 3 / / MEMORY CLEAR MEMORY REMOTE CONTROLLER RC-331C 1 2 3 4 5 6 7 8 9 +10 0 flash on the time display to indicate that the memory is full. Press the The CD changer will play the programmed tracks in the order you selected. · If you press the MEMORY button during playback, the track being played will be stored in memory. [. . . ]