User manual ONKYO DX-7711

[. . . ] Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain the optimum performance and listening enjoyment from your new DX-7711. Please retain this manual for future reference. Main Features · · · · · · CD/CD-R/CD-RW Disc Compatibility Auto Finalizing Function 32kHz/44. 1kHz/48kHz Sampling-Rate Converter 1 Optical/1 Coaxial Digital Inputs Signal Synchro Recording Name input function allowing you to specify a disc name, track titles, and an artist name. · Adjustable Recording Volume (Digital/Analog) · High-Resolution D/A & A/D Converter · 1 Optical/1 Coaxial Digital Outputs · z Cable Included WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] When you turn the main power on first time, the standby indicator lights and the DX-7711 enters the standby state. If you turn off the main power last time with the DX-7711 turned on, without pressing the STANDBY/ON button the recorder will be automatically turned on after pressing the POWER switch next time. In this case, if the CD is already loaded, the DX-7711 will automatically start playback. STANDBY When a malfunction occurs The DX-7711 employs a microcomputer to realize its advanced features. Although quite rare, occasionally noise from outside the unit, interruption noise, or static electricity may cause a malfunction. If a malfunction occurs, unplug the power cord and after about 5 seconds plug it in again. Note: The DX-7711 is shipped with the main power (POWER) switch in the on position. When the power cord is plugged in for the first time, the DX-7711 will automatically enter the standby state and the standby indicator will light (same condition after step 1 on the left). POWER ON OFF 2 Press the STANDBY/ON button. The STANDBY indicator goes out and the display panel lights. DX-7711 STANDBY/ON RC-448C STANDBY/ ON STANDBY The STANDBY indicator turns off. 16 Inserting a disc Disc tray r STANDBY/ ON OPEN / CLOSE RANDOM MEMORY REPEAT r OPEN/ CLOSE ABC DUAL DIGITAL INPUT STANDBY/ON PAUSE STOP PLAY DEF 3 NAME 1 2 GHI 4 MEMORY STANDBY CLEAR DISPLAY MULTI JOG INPUT JKL 5 MNO 6 SCROLL PQRS PHONES REPEAT FINALIZE EDIT/ NO PUSH TO ENTER TUV 8 W XYZ 9 CLEAR PHONES LEVEL POWER YES 7 REC DISPLAY MIN MAX ENTER ON OFF AUDIO CD RECORDER DX-7711 >10 10/0 REC 1 Turn on the DX-7711. Place the disc with the label-side up in the center of the tray. DX-7711 RC-448C · When the disc is inserted, the DX-7711 automatically scans the disc and displays the type in the front display. Disc indicator CD label-side CD-R CD-RW 3 Press the r button. The disc tray closes. · By pressing the r button in the standby state, the power is automatically turned on. CD-RW FINALIZE Commercially sold CD Finalized CD-R Unrecorded CD-R Partly recorded (not finalized) CD-R Unrecorded CD-RW Partly recorded (not finalized) CD-RW Finalized CD-RW · The DX-7711 displays information of the disc, including total recording number of tracks and time, and remaining available recording time. When unrecorded compact discs are inserted, "Blank Disc" appears in the display. 17 Recording modes Cautions during recording In the following situations, recording is not possible even if the o REC button is pressed. · The CD indicator is lit (a CD or finalized CD-R has been inserted). · The CD-RW and FINALIZE indicators are lit (a finalized CD-RW has been inserted). · The inserted disc is full and "Disc Full" is displayed. · Place a recordable CD-R or CD-RW in the DXR700 (see page 17). · Verify that the input dial and recording selection button of the amplifier are set to the position of the recording source. 2 Start playback of the recording source. 3 Press the o REC button. The level sync function is set to On (see page 26). "Rec setup" appears in the display followed by the time display (the recording standby state). DX-7711 REC RC-448C REC Proceed to step 6 if you do not wish to adjust the recording level. Note: When you select the digital input but the digital cable is not connected to the DX-7711, "D. InUnlock" will appear. 20 Digital recording/Analog recording 4 Adjust the recording level. (1) Press the EDIT/NO button and turn the MULTI JOG dial until "Rec Level?" appears. MULTI JOG EDIT/ NO (4) After adjusting the recording level, press the MULTI JOG dial. Pressing the YES button provides the same operation. MULTI JOG PUSH TO ENTER PUSH TO ENTER 5 Stop the playback of the recording (2) Press the MULTI JOG dial. Pressing the YES button provides the same operation. Press the EDIT/NO button if you cancel the adjustment operation. source. 6 Press the s button and start the recording source. Recording starts. After the recording reaches the end of the disc, the DX-7711 will stop. (3) Turn the MULTI JOG dial to adjust the recording level as desired. The current level is displayed, ranging from - to +20 dB. MULTI JOG To set the track numbers manually Press the o REC button. To pause the recording PUSH TO ENTER For analog recording Adjust so that when the recording level is at its highest, it does not reach "OVER" in the front display. If OVER is reached, the sound becomes distorted. Adjust the level so that "OVER" will not light. Press the g button. To resume recording, press the s button when the time display appears. If the entire disc becomes filled with recordings, the DX-7711 automatically stops. To stop the recording Press the e button. Notes: · When digitally recording satellite broadcasts, the track numbers may not be assigned properly. [. . . ] Remedy Eject the disc and check whether it meets the specifications for use with the DX-7711. Always insert a disc that has the markings "FOR CONSUMER" or "FOR MUSIC USE ONLY" on its surface (see page 12). Record from a recordable source. Check Input Synchronous recording cannot be performed because the detected input signal is from a source other than the CD, MD, DAT, or DCC. Recording cannot be performed because a finalized CD-RW is used. Cannot Rec Replace it with a non-finalized CD-R. [. . . ]