User manual ONKYO ED-301

[. . . ] Contents Important Safeguards 2 Digital Surround Processor Precautions 3 ED-301 Instruction Manual POWER PARAMETER CONTROLLER INPUT-1 INPUT-2 LISTENING MODE CINEMA Re-EQ Features 4 Before using this unit 5 System configuration 6 Connections 7-9 ON OFF TEST TONE DIMMER SPEAKER DISTANCE LEVEL MULTI-CH INPUT MIDNIGHT THEATER LFE LEVEL VOLUME Speaker setting and distance setting 10-11 DIGITAL SURROUND PROCESSOR ED-301 Output level setting 12-13 Playing surround sounds 14-15 Thank you for purchasing the ONKYO ED-301 Digital Surround Processor. Please read this manual thoroughly before making connections and turning on the unit. Following the instructions in this manual will enable you to obtain the optimum performance and maximum listening enjoyment from your new ED-301. Please retain this manual for future reference. Setting the listening mode 16-17 Position and name of each control 18 Troubleshooting 19 Specifications 20 WARNING "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION "TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Caution: If your speakers are connected via three independent power amplifiers, do not connect an external decoder or DVD player to the MULTI-CHANNEL AUDIO INPUT jacks of the ED-301. Doing so may cause damage to the power amplifiers or speakers because there is no means of adjusting the output level. : Signal flow INPUT-1 INPUT-2 OUTPUT INPUT-1 INPUT-2 OUTPUT DIGITAL SURROUND PROCESSOR S-VIDEO LEFT LEFT SURROUND CENTER VIDEO MULTI-CHANNEL AUDIO OUTPUT LEFT MODEL NO. LEFT CENTER SURROUND RATING: ED-301 INPUT-1 ( OPTICAL ) INPUT-2 ( COAXIAL ) To power outlet L DB-25 R RIGHT SUB RIGHT SURROUND WOOFER 2-1, NISSHIN-CHO, NEYAGAWA-SHI, OSAKA, JAPAN MADE IN JAPAN AC 220- 230V RIGHT SUB RIGHT SURROUND WOOFER AC 120V VOLTAGE SELECTOR MULTI-CHANNEL AUDIO INPUT L R R L Do not plug the power cord until all connections are made. Supplied video connection cable Supplied stereo audio connection cable Supplied monaural audio connection cable Line input L R L R Line input INPUT or LINE IN Line input INPUT or LINE IN INPUT or LINE IN S-Video input Video input Line input Monitor TV Left Front speaker Right Front speaker Left Surround speaker Right Surround speaker Powered subwoofer Subwoofer Center speaker Note: Refer also to your TV monitor's owner's manual for video and S-video connection. 9 Speaker setting and distance setting Set the ED-301 properly for your speaker system. If your ED-301 is connected to an A/V amplifier with 5. 1-channel audio input, also perform speaker setting on the A/V amplifier. Speaker setting procedure 1 3 2 Speaker setting Set one of the following parameters for each speaker type. For a typical speaker system with six speakers, set "LARGE/SMALL" or "YES" for all speaker types. Set this parameter if the connected speaker(s) can cover the bass range. SMALL Set this parameter if the connected speaker(s) cannot cover the bass range. YES Set this parameter if you connect a center speaker, surround speakers, or a subwoofer. NONE or NO Set this parameter if there is no speaker connected to that channel and output is to be made to other speakers. Available combination of setting for each speaker type Speaker type SW (Subwoofer) L/R (Front) C (Center) LS/RS (Surround) SMALL LARGE 3 1 2 Press POWER. Do not press MULTI-CH INPUT or you will be unable to go on to the next and later steps. Press SPEAKER repeatedly to select the speaker type for the speaker you are setting and then press PARAMETER CONTROLLER repeatedly to select the parameter you want to set. Each time you press the SPEAKER button, the speaker indicator(s) that is blinking changes as follows. SW (Subwoofer) L/R (L/R Front) C (Center) LS/RS (L/R Surround) COMPLETE Speaker setting indication 3 Possible parameter setting YES LARGE NO Setting LARGE automatically brings up selection for next speaker type. YES/NO LARGE/SMALL/ LARGE/SMALL/NONE NONE YES/NO LARGE/SMALL/ LARGE/SMALL/NONE NONE INPUT-1 DOLBY DIGITAL L R Note: The following is the factory-set parameter for each speaker type: SW : YES L/R : SMALL C : YES LS/RS : YES Indicator for speaker(s) being set When the setting for the current speaker type has been done, press SPEAKER and the speaker indicator(s) for the next speaker type will blink. You will get out of the speaker setting mode if the speaker setting operation is interrupted for 3 seconds or longer. To return to the speaker setting mode in this case, press the SPEAKER button again. Speaker setting and listening mode If system includes Surround speakers but lacks a Center speaker. . . PHANTOM mode L C R L If system includes a Center speaker but lacks Surround speakers. . . 3 STEREO mode C R If system lacks both a Center and Surround speakers. . . STEREO mode L C R LS RS LS RS LS RS SW L/R C LS/RS : YES or NO : SMALL or LARGE : NO or NONE : SMALL or LARGE SW L/R C LS/RS : YES or NO : SMALL or LARGE : YES, or SMALL or LARGE : NO or NONE SW L/R C LS/RS : YES or NO : SMALL or LARGE : NO or NONE : NO or NONE 10 Speaker setting and distance setting Distance setting procedure Distance setting For each speaker type, set the distance from your listening position to where the speaker is located. 1 4 2 Left Front speaker Center speaker Right Front speaker 3 L C R Subwoofer 1 2 Left Surround speaker LS Listening position RS Right Surround speaker 3 Press POWER. Do not press MULTI-CH INPUT or you will not be able to go to the next and later steps. Press DISTANCE repeatedly to select the speaker type for which you are setting the distance and then press PARAMETER CONTROLLER to display the parameter you want to set. Each time you press the DISTANCE button, the speaker indicator(s) that is blinking changes as follows. L/R (L/R Front) C (Center) LS/RS (L/R Surround) COMPLETE Press the PARAMETER CONTROLLER button to display parameter you want to set while the speaker indicator is blinking. L/R: Distance from listening position to L/R Front speaker position. LS/RS: Distance from listening position to L/R Surround speaker position. Distance setting indication Indicator for speaker(s) for which setting is being made INPUT-1 DOLBY DIGITAL ft L R Indication in meters Indication in feet The distance setting can be adjusted in units of 1 foot (0. 3 meter). L/R: Set the actual distance from listening position to L/R Front speaker position, within the range of 1 - 30 feet (0. 3 - 9. 0 meters). [. . . ] This unit contains a sensitive microcomputer, which under certain circumstances might fail to operate due to excessive noise interference. In such an event, disconnect the main plug from your electrical outlet and replace it after 5 seconds. Remedy · Insert the unit's power plug completely to a power outlet. · Turn on the amplifier's power switch. The sound is not reproduced by the correct speakers. [. . . ]