User manual ONKYO EQ-201

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] The M. Opt indicator lights on the display. Tip · Alternatively, you can use the remote controller's HOME and arrow buttons. · See "Music Optimizer" for more details ( page 44). En 32 Muting the AV Receiver You can temporarily mute the output of the AV receiver. Recording Separate AV Sources Here you can record audio and video from completely separate sources, allowing you to overdub audio onto your video recordings. This function takes advantage of the fact that when an audio-only input source (TV/CD) is selected, the video input source remains unchanged. In the following example, audio from the CD player connected to the TV/CD IN and video from the camcorder connected to the AUX INPUT VIDEO are recorded by the VCR connected to the VCR/DVR OUT jacks. Camcorder 1 Press RECEIVER followed by MUTING. The output is muted and the MUTING indicator flashes on the display. Tip · To unmute, press MUTING again or adjust the volume. · The mute is cancelled when the AV receiver is set to Standby. Using Headphones 1 Connect a pair of stereo headphones with a standard plug (1/4 inch or 6. 3 mm) to the PHONES jack. Note · Always turn down the volume before connecting your headphones. · While the headphones plug is inserted in the PHONES jack, the speakers are turned off. · When you connect a pair of headphones, the listening mode is set to Stereo, unless it's already set to Stereo, Mono, or Direct. Recording This section explains how to record the selected input source to a component with recording capability, and how to record audio and video from different sources. CD player VCR : Video signal : Audio signal AV Recording Audio sources can be recorded to a recorder (e. g. , cassette tape deck, CDR, MD recorder). Video sources can be recorded to a video recorder (e. g. , VCR, DVD recorder). 1 2 3 4 5 1 Use the input selector buttons to select the source that you want to record. The AV receiver's MASTER VOLUME control has no effect on recording. If you select another input source during recording, that input source will be recorded. Prepare the camcorder and CD player for playback. Here you can check the settings made by Audyssey 2EQ Room Correction and Speaker Setup, or set them manually, which is useful if you change one of the connected speakers after using Audyssey 2EQ Room Correction and Speaker Setup. This section explains how to specify which speakers are connected and their sizes. For speakers with a cone diameter larger than 6-1/2 inches (16 cm), specify Large Cone diameter (full band). For those with a smaller diameter, specify Small (default crossover 100 Hz). The crossover frequency can be changed in the "Crossover (Crossover Frequency)" ( page 36). Note · These settings are not available in either of the following cases: ­ a pair of headphones is connected. ­ the "Audio TV Out" setting is set to "On" ( page 42). ­ "HDMI Ctrl (RIHD)" is set to "On" ( page 42) and you're listening through your TV speakers. Surround Back Ch 1ch: Select if only one surround back speaker is connected. 2ch: Select if two (left and right) surround back speakers are connected. Note · If the "Surround Back" setting is set to "None", this setting cannot be selected. Crossover (Crossover Frequency) This setting is advantageous for the speakers that you specified as "Small" in the "Sp Config (Speaker Configuration)" ( page 36). To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your speakers. 40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz, 120Hz, 150Hz, 200Hz Use the diameter of the smallest speaker in your system when choosing the crossover frequency. Speaker cone diameter Over 8 in. (9 cm) * Crossover frequency 40/50/60 Hz* 70/80/90 Hz* 100 Hz 120 Hz 150/200 Hz* Subwoofer Yes No Front Small: Large: Select based on the cone diameter. Note · If the "Subwoofer" setting is set to "No", this setting is fixed at "Large" and does not appear. Choose the setting suitable for the speaker. [. . . ] · Operation of the player/recorder is possible with the remote controller supplied with the AV receiver. * The following components are of January 2011) TV · Toshiba REGZA-LINK compatible TV · Sharp TV Players/Recorders · Onkyo and Integra -compatible players · Toshiba REGZA-LINK compatible players and recorders (only when used together with Toshiba REGZA-LINK compatible TV) · Sharp players and recorders (only when used together with Sharp TV) * Models other than those mentioned above may have some interoperability if compatible with CEC which is part of the HDMI Standard, but operation cannot be guaranteed. Note · Do not connect the -compatible component more than the following number to the HDMI input terminal so that the linked operations work properly. ­ Blu-ray Disc recorder/DVD recorder/Digital Video Recorder is up to three. · Do not connect the AV receiver to the other AV receiver/AV amplifier via HDMI. · When the -compatible component more than the above-mentioned is connected, the linked operations are not guaranteed. Not all functions may operate depending on the model. En 57 How to connect and setup 3 1 Confirm the connecting and setting. [. . . ]