User manual ONKYO HT-R320

[. . . ] Contents Before using AV Receiver HT-R320 Instruction Manual Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Facilities and connections Index to parts and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Each press of the button switches the displayed input format as follows: Auto ( )* Multich** Analog Auto (back to the beginning) * The name of the input terminals (OPT or COAX) is shown inside ( ). "Auto" will be skipped when digital input jack is not assigned to the input source. ** "Multich" can be selected only when DVD is selected as the input source. To fix the "Auto" to DTS or PCM If there is a problem as described below, it is possible to fix the "Auto" to PCM or DTS. · If the beginning of each PCM track is cut in Auto mode Fix the digital signal to PCM. However, care is required in using this mode for playback of a DTS-CD may be interfered by noise. · If, during playback of a DTS-CD in Auto mode, noise is output when the CD is fast-forwarded or reversed Fix the digital signal to DTS. 1) Press AUDIO SELECTOR on the main unit (or AUDIO SEL on the remote controller) to select "Auto". Each 2) While "Auto" is displayed, press ADJUST press of the button switches the display between Auto PCM DTS Auto. When the digital signal is fixed at DTS or PCM, the digital signal is reproduced only when the selected type of signal is input. In this case, only the indicator of the non-reproduced source (PCM or DTS) will blink. Note Changing the digital input setting (see page 21) will cancel the selected input signal format. If you had set the DVD input to "Multi", it will not change. Note · Any speaker that is not included in the speaker configuration on page 18 is not selected even if it is actually connected. · The subwoofer will not output the test tone if it's off. Press CH SEL repeatedly to select the speaker, then press LEVEL / to adjust the volume level. The volume level can be adjusted between ­12dB and +12dB in 1 dB steps. When TEST is pressed after the above adjustment, the set levels will become the levels adjusted using the test tone by overwriting the existing ones. 26 Enjoying multi channel sources SURROUND DIRECT DIRECT Before operating the remote controller, press RCVR/TAPE. SURROUND CH SEL AUDIO SEL DVD AUDIO SELECTOR DVD TAPE LEVEL Using analog multi channel input The multi channel input refers to a system, which is compatible with a source component equipped with analog 5. 1-channel outputs (DVD player, MPEG decoder, etc. ), reproducing the left/right front, center and left/right surround channels from five respective speakers and outputting the subwoofer channel from SUB WOOFER (refer to page 13). 1. Press AUDIO SELECTOR on the unit or AUDIO SEL on the remote controller repeatedly to select "Multich". Turn on the component connected to the DVD (FRONT L/R, SURR L/R, CENTER and SUBWOOFER) port and start playing the desired media. Check that the DVD player is set for multi channel output. See instruction manual supplied with your DVD player for details. Notes · "Multich" can be selected only when DVD is selected as the input source. · The surround mode cannot be selected when "Multich" is selected. Also, if "Multich" is selected during use of a surround mode, it is canceled automatically. · Regardless of the speaker configuration, the input signal will be output to each corresponding speaker. [. . . ] If any of the following signals are fed to them, even if the input power is within the specified rating, excessive current may flow in the speaker coils, causing burning or wire breakage: 1. High-pitched sounds generated by an oscillator, electronic musical instrument, and so on. Thumps and clicks caused by connecting or disconnecting audio cables (Always turn off your amplifier before connecting or disconnecting cables. ) 7. Microphone feedback. Using Close to a TV or Computer TVs and computer monitors are magnetically sensitive devices and as such are likely to suffer discoloration or picture distortion when conventional speakers are placed nearby. [. . . ]