User manual ONKYO HT-R520

[. . . ] 2 AV Receiver HT-R520 Instruction Manual Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. Advanced Operation . . . . . . . . . . . . . . . . . . . . . [. . . ] Repeat this step to select TAPE, MD, or CDR. TAPE CD Press the input selector button for the source that you want to assign. (Digital inputs cannot be assigned to the TUNER input source. ) 2 DIGITAL INPUT Press the [DIGITAL INPUT] button. The current assignment appears. 3 DIGITAL INPUT Press the [DIGITAL INPUT] button repeatedly to select COAX, OPT1, OPT2, OPT3, or ­ ­ ­ ­. 31 Playing Your AV Components This chapter explains how to use the HT-R520 with your other AV components. Selecting the Source Component 1 V1 ON STANDBY I AMP V2 V3 TV INPUT DVD Press the [AMP] button followed by an input selector button to select the component that you want to play. The name of the selected source appears on the display, as shown. A & B speakers indicators Volume V1 V2 V3 1 2 MULTI CH 3 6 TUNER + TV CH Input selector buttons DVD 4 CD 5 TAPE - MULTI CH CD TAPE TUNER 7 +10 --/--TONE 8 0 9 T V VOL CLEAR _ TUNER/ TAPE + MD AMP REMOTE MODE DVD CD CDR AMP Selected input source TV VCR CABLE SAT DIMMER TV INPUT P TO MEN SLEEP U MEN U 2 VOL SP A AMP + CH DISC ENTER VOL EX IT DISPLAY PREV CH RE E GUID TUR N UP SET DISPLAY MUTING SP B REC SP A SP B RANDOM SP A SP B CH SEL AUDIO SURR SUBTITLE ALL ST ANGLE LAST M STEREO REPEAT A-B DIRECT SEARCH DSP MEMORY DSP Use the [SP A] and [SP B] buttons to select the speaker set that you want to use. The A and B speaker indicators show whether each speaker set is on or off. Note: When you turn on speaker set B, the listening mode for speaker set A is set to Stereo automatically. To adjust the volume, use the MASTER VOLUME control or the remote controller's VOL button. The volume can be set to MIN, 1 though 79, or MAX. TEST TONE CH SEL LEVEL - LEVEL+ OPEN/CLOSE VIDEO OFF OR-EQ L NIGHT CINE FLTR LEVEL +/­ RC-570M 3 4 VOL 5 Enjoy listening modes. See page 38. 32 Playing Your AV Components--Continued Displaying Source Information You can display various information about the current input source as follows. Press the [DISPLAY] button repeatedly to cycle through the available information. Using the Multichannel Input The multichannel input is for connecting a component with individual 5. 1-channel analog audio outputs, such as a DVD player or MPEG decoder. See "DVD Multichannel Connection" on page 24 for connection information. DISPLAY 1 The following information can typically be displayed for input sources. Input source & volume AMP MULTI CH Press the [AMP] button followed by the [MULTI CH] button so that "MULTI" appears on the display. Audio from the multichannel input will now be used for the DVD input source. Signal format* or sampling frequency Input source & listening mode 2 CH SEL *If the input signal is analog, no format information is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about three seconds, then the previously displayed information reappears. Interpreting Surround Channel Information LEVEL- LEVEL+ To adjust the level of individual speakers, use the remote controller's [CH SEL] button to select them, and then use the [LEVEL­] and [LEVEL+] buttons. The level can be adjusted from ­12 to +12 dB in 1 dB steps (­15 to +12 dB for the subwoofer). A BC A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). If there's a surround back channel information, this number will be 3. C: LFE channel for subwoofer (1 means yes). Note that the individual speaker level settings for the multichannel input are independent of those explained on page 47. Notes: · While the multichannel input is selected, you can select only the Direct listening mode. If you select the multichannel input while using another listening mode, that listening mode is cancelled. · While the multichannel input is selected, the Speaker Configuration settings on page 48 are ignored, and signals from the multichannel input are fed to the front left, front right, center, surround left, and surround right speakers and subwoofer regardless of those settings. 33 Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. [. . . ] Or, your FM antenna is in the wrong position or pointing in the wrong direction. Installing an outdoor antenna is a specialist job, so contact your nearest dealer for advice (page 19). Interference is being caused by fluorescent lights being turned on or off or by passing cars. AM reception is hindered by a buzzing noise, especially at night or with weak signals? [. . . ]