User manual ONKYO HT-R640

[. . . ] Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver HT-R640 Instruction Manual Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 First Time Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Basic Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Advanced Operations. . . . . . . . . . . . . . . . . . . . 62 Advanced Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Controlling Other Components . . . . 72 Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Information is displayed for about three seconds, then the previously displayed information reappears. Interpreting Surround Channel Values 2 Use the TONE [­]/[+] buttons to adjust. A BC I Bass You can boost or cut low-frequency sounds output by the front speakers from ­10 dB to +10 dB in 2 dB steps. I Treble You can boost or cut high-frequency sounds output by the front speakers from ­10 dB to +10 dB in 2 dB steps. A: The number of front channels (3 means front left, front right, and center). B: The number of surround channels (2 means surround left and surround right). C: LFE channel for subwoofer (1 means yes). 46 Basic Operations--Continued Press [RECEIVER] or [AMP] first Using the Sleep Timer With the sleep timer, you can set the AV receiver to turn off automatically after a specified period. AMP RECEIVER STANDBY/ON REMOTE MODE RECEIVER TAPEAMP DVD M D/CDR INPUT SELECTOR 1 V1 2 V2 3 V3 CD HDD 4 V4 5 MULTI CH 6 DVD TV 7 TAPE 8 TUNER 9 CD VCR 12 CABLE 10 11 +10 0 ENT DIMMER CLR SLEEP SAT DIMMER D TUN --/--- SLEEP VOL TV INPUT GUIDE TOP MENU VOL DISC ALBUM CH Press the [RECEIVER] or [AMP] button, and then press the [SLEEP] button repeatedly to select the required sleep time. The SLEEP indicator appears on the display when the sleep timer has been set. The specified sleep time appears on the display for about five seconds, then the previous display reappears. PREVIOUS MENU MUTING MUTING ENTER PLAYLIST/CAT PLAYLIST/CAT SLEEP Setting the Display Brightness You can adjust the brightness of the display. AMP RECEIVER If you need to cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the time remaining until the AV receiver sleeps, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. DIMMER Press the [RECEIVER] or [AMP] button, and then press the [DIMMER] button repeatedly to select: · Normal+VOLUME light on. · Dimmer+VOLUME light off. Using Headphones You can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver's PHONES jack for private listening, as shown. Muting the AV Receiver You can temporarily mute the output of the AV receiver. AMP RECEIVER Press the [RECEIVER] or [AMP] button, and then press the [MUTING] button. The output is muted and the MUTING indicator flashes on the display, as shown. MUTING To unmute the AV receiver, press the [MUTING] button again, or adjust the volume. The Mute function is cancelled when the AV receiver is set to Standby. Notes: · Always turn down the volume before connecting your headphones. · The speakers are turned off while the headphones plug is inserted in the PHONES jack. · When you connect a pair of headphones, the listening mode is set to Stereo, unless it's already set to Stereo, Mono, Direct, or Pure Audio (not North American models). · Only the Stereo, Direct, Pure Audio (not North American models), and Mono listening modes can be used with headphones (the listening modes available also depend on the currently selected input source). · When the multichannel input is used, only the front left and right audio can be heard in the headphones. · To adjust the headphone level, press the [CH SEL] button on the remote controller, and then press the [LEVEL +]/[LEVEL -] buttons. You can adjust the level between ­12 dB and +12 dB. 47 Listening to the Radio Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. I Manual Tuning Mode 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. Listening to the Radio 2 TUNER TUNING PRESET Use the [TUNER] input selector button to select either AM or FM. Each time you press the [TUNER] button, the input source changes between AM and FM. Press and hold the TUNING Up or Down [ ]/[ ] button. Press the buttons repeatedly to change the frequency one step at a time. Band Frequency The North American models change FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For other models it's 0. 05 MHz steps for FM and 9 kHz steps for AM. [. . . ] · When using the remote controller to control other manufacturers' AV components, some buttons may not work as expected. · Make sure you've entered the correct remote control code. · Make sure to set the same ID on both the AV receiver and remote controller (pages 69 and 71). Can't control other components · If it's an Onkyo component, make sure that the cable and analog audio cable are connected properly. [. . . ]