User manual ONKYO HT-S3200

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5. 1ch Home Theater System Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 HT-S3200 AV Receiver (HT-R370) Speaker Package (HTP-370) Turning On & First Time Setup . . . 35 Basic Operations. . . . . . . . . . . . . . . . . . . . . . . . . 38 Instruction Manual Using the Listening Modes . . . . . . . . 47 Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Controlling Other Components. . . 60 Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Thank you for purchasing an Onkyo 5. 1ch Home Theater System. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new 5. 1ch Home Theater System. Please retain this manual for future reference. En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] · Speaker sets A and B are turned off while the headphones plug is inserted in the PHONES jack. · When you connect a pair of headphones, the listening mode is set to Stereo, unless it's already set to Mono, Stereo, or Direct, in which case it stays the same. Note: This procedure can also be performed on the AV receiver by using its [DISPLAY] button. The following information can typically be displayed: Input source & volume*1 Signal format*2 or sampling frequency Input source & listening mode *1 When AM or FM radio is used, the band, preset number, and frequency are displayed. *2 If the input signal is analog, or AM or FM radio is selected, no format information is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears. Adjusting the Bass & Treble You can adjust the bass or treble for speaker set A's front speakers, except when the Direct listening mode is selected. AV receiver Press the [TONE] button repeatedly to select either "Bass" or "Treble". Use the TONE [­]/[+] buttons to adjust. Interpreting Surround Channel Information A Remote controller BC Tip: This procedure can also be performed on the remote controller by using [AUDIO] button (see page 58). A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). C: LFE channel for subwoofer (1 means yes). Bass You can boost or cut low-frequency sounds output by the front speakers from ­10 dB to +10 dB in 2 dB steps. Treble You can boost or cut high-frequency sounds output by the front speakers from ­10 dB to +10 dB in 2 dB steps. 40 Basic Operations--Continued Using the Music Optimizer The Music Optimizer function enhances the sound quality of compressed music files. Use it with music files that use "lossy" compression, such as MP3. To turn the Music Optimizer "On" or "Off", use the AV receiver's [MUSIC OPTIMIZER] button. Tip: This procedure can also be performed on the remote controller by using [AUDIO] button (see page 59). Note: The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48 kHz and analog audio input signals. The Music Optimizer is disabled when the Direct listening mode is selected. Specifying the Digital Signal Format The following table shows the display indicator for each digital signal format. Format Dolby Digital DTS PCM PCM Display Normally, the AV receiver detects the format of digital input signals automatically. However, if you experience either of the following issues when playing PCM or DTS sources, you can specify the signal format manually. · If the beginnings of tracks from a PCM source are cut off, try the PCM setting. · If noise is produced when fast forwarding or rewinding a DTS CD, try the DTS setting. , AUDIO 1 Press and hold [AUDIO] button for about 8 seconds. 2 While "Auto" is displayed (about 3 seconds), use the Left and Right [ ]/[ ] buttons to select: PCM, DTS, or Auto. If the input signal is not PCM, the PCM indicator will flash and there will be no sound. If the input signal is not DTS, the DTS indicator will flash and there will be no sound. If no digital input signal is present, the corresponding analog input is used instead. 41 Listening to the Radio AM/FM Frequency Step Setup 4 RECEIVER ENTER SETUP Use the Left and Right [ ]/[ ] buttons to select: (North American/Taiwan models) 200k/10k: Select if 200k/10k steps are used in your area. Setup closes. For AM/FM tuning to work properly, you must specify the AM/FM frequency step used in your area. [. . . ] · To control an Onkyo component that's connected via , point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first (page 61). Others The sound changes when I connect my headphones · When a pair of headphones is connected, the listening mode is set to Stereo, unless it's already set to Stereo, Mono or Direct in which case it stays the same. How do I change the language of a multiplex source · On the "7. Audio Adjust" menu, change the "Input (Mux)" setting to "Main" or "Sub" (page 55). [. . . ]