Detailed instructions for use are in the User's Guide.
[. . . ] 2
5. 1ch Home Theater System
HT-S4100
AV Receiver (TX-SR304) Front Speakers (SKF-360F L/R) Center Speaker (SKC-360C) Surround Speakers (SKM-360S L/R) Subwoofer (SKW-460) Remote Interactive Dock (DS-A1XP)
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new 5. 1ch Home Theater System. Please retain this manual for future reference.
Advanced Operation . . . . . . . . . . . . . . . . . . . . . [. . . ] Note: · If the Subwoofer setting in step 3 is set to No, this setting is fixed at Large and does not appear.
4
38
First Time Setup--Continued
5
Use the Down [ ] button to select "Center, " and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected.
Testing the speakers To test that all of the speakers are working properly, press the remote controller's [TEST TONE] button.
LISTENING MODE STEREO SURROUND
AUDIO SUBTITLE RANDOM REPEAT
TEST TONE
TEST TONE
CH SEL PLAY MODE
LEVEL-
LEVEL+
DISPLAY
L NIGHT
CINE FLTR
RC-645S
6
Use the Down [ ] button to select "Surround, " and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected.
The test tone will be output by each speaker in turn and the name of each speaker will appear on the display. · If the test tone is not produced by a speaker, or it's produced by a speaker other than that shown on the display, you may have wired the speakers incorrectly and you should check your connections (see pages 21, 22). · If the test tone is not produced by a speaker and its name does not appear on the display, you may have set the speaker settings incorrectly (see page 38).
7
SETUP
Press the [SETUP] button. When you want to go back up one menu level to "SP Config, " press the [RETURN] button.
39
Playing Your AV Components
Basic AV Receiver Operation
ON/STANDBY REMOTE MODE
RECEIVER
TAPE
DVD
1
Subwoofer's rear panel
2
STANDBY/ON
STANDBY
DISPLAY
TUNING / PRESET
4
MASTER VOLUME
ENTER
1
INPUT SELECTOR
1
V1
2
V2
3
V3
CD
4 7
TAPE
5
MULTI CH
6
DVD
MD
8
TUNER
9
CD
CDR
+10
--/--TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP
0
DIMMER
CLR
SLEEP
HDD
A SPEAKERS B
CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD
DISC ALBUM
CH
VOL
4
4
MIN MAX
MULTI CH
1
2
GUIDE TOP MENU
PREVIOUS MENU
OUTPUT LEVEL
SP A / B
MUTING
ENTER PLAYLIST PLAYLIST
1
AV receiver
DVD VIDEO 1/VCR VIDEO 2
Remote controller
RECEIVER
Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1/VCR, VIDEO 2, and VIDEO 3 input sources respectively.
VIDEO 3
TAPE
TUNER
V1
CD
V2
V3
DVD
TAPE
TUNER
CD
2
AV receiver
A SPEAKERS B
Remote controller
SP A / B
Use the SPEAKERS [A] and [B] buttons on the AV receiver or the [SP A/B] button on the remote controller to select the speaker set that you want to use. Pressing the remote controller's [SP A/B] button cycles through the following settings: Speaker Set A Speaker Set A&B Speaker Set B Off. The A and B speaker indicators show whether each speaker set is on or off. Indicators Note that when speaker set B is turned on, speaker set A is reduced to 2. 1-channel playback.
3 4
AV receiver
MASTER VOLUME
Start playback on the source component. When you select DVD or another video component, on your TV you'll need to select the video input that's connected to the AV receiver's MONITOR OUT.
Remote controller
VOL
To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The AV receiver is designed for home theater enjoyment and has a wide volume range for precise adjustment. Note: When the subwoofer volume level is set to a positive (+) value, the maximum master volume level is reduced proportionally. Because our ears are less sensitive to very low bass sounds, there's a temptation to set the level of the subwoofer too high. As a rule of thumb, set the subwoofer level to what you think is the optimal level, and then back it off slightly.
5
40
Select a suitable listening mode and enjoy!See "Using the Listening Modes" on page 49.
Playing Your AV Components--Continued
Using the Multichannel Input
You can display various information about the current input source as follows.
RECEIVER
ON/STANDBY REMOTE MODE
RECEIVER
1
V1
RECEIVER
TAPE
DVD
INPUT SELECTOR
2
V2
3
V3
CD
DISPLAY
Press the [RECEIVER] button, and then press the [DISPLAY] button repeatedly to cycle through the available information.
MULTI CH
4 7
TAPE
5
MULTI CH
6
DVD
MD
8
TUNER
9
CD
CDR
+10
--/---
0
DIMMER
CLR
SLEEP
HDD
The following information can typically be displayed for input sources.
Input source & volume*1 Signal format*2 or sampling frequency Input source & listening mode
DISC ALBUM
CH
VOL
The multichannel input is for connecting a component with individual 5. 1-channel analog audio output jacks, such as a DVD player or MPEG decoder. See page 29 for hookup information.
RECEIVER
Press the [RECEIVER] button followed by the [MULTI CH] button so that MULTI CH indicator appears on the display. Audio from the multichannel input will now be used for the DVD input source.
MULTI CH indicator
MULTI CH
*1 When AM or FM radio is used, the band, preset number, and frequency are displayed. *2 If the input signal is analog, or AM or FM radio is selected, no format information is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears. [. . . ] Always remove your iPod from the case before inserting it into the RI Dock. · The iPod cannot be operated while it's displaying the Apple logo. · When you use the AV receiver's remote controller, point it toward your AV receiver. · The RI Dock must be connected to the AV receiver with both an cable and an audio cable. [. . . ]