User manual ONKYO HT-S6200

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7. 1ch Home Theater System Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 HT-S6200 AV Receiver (HT-R670) Speaker Package (HTP-670) Front Speakers (SKF-670) Center Speaker (SKC-670) Surround Speakers (SKR-670) Surround Back Speakers (SKB-670) Powered Subwoofer (SKW-770) Turning On & First Time Setup . . . 40 Basic Operations. . . . . . . . . . . . . . . . . . . . . . . . . 49 Dock for iPod (UP-A1) Using the Listening Modes . . . . . . . . 61 Instruction Manual Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Zone 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Controlling Other Components. . . 84 Thank you for purchasing an Onkyo 7. 1ch Home Theater System. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new 7. 1ch Home Theater System. Please retain this manual for future reference. Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] · Auto Power On Function If you start iPod or iPhone playback while the AV receiver is on Standby, the AV receiver will automatically turn on and select your iPod or iPhone as the input source. · Direct Change Function If you start iPod or iPhone playback while listening to another input source, the AV receiver will automatically select your iPod or iPhone as the input source. · Using the AV receiver's Remote Controller You can use the AV receiver's remote controller to control basic iPod or iPhone functions. Putting Your iPod/iPhone in the Dock 1. Align your iPod or iPhone with the Dock connector, and carefully place your iPod or iPhone in the slot, as shown. Remove case before inserting 57 UP-A1 series Dock for iPod/iPhone--Continued Operating Notes: · Before selecting a different input source, stop iPod or iPhone playback to prevent the AV receiver from selecting the iPod or iPhone input source by mistake. · If any accessories are connected to your iPod or iPhone, the AV receiver may not be able to select the input source properly. · While your iPod or iPhone is in the UP-A1 series Dock, its volume control has no effect. If you adjust your iPod or iPhone models volume control while it's in the UP-A1 series Dock, make sure it's not set too high before you reconnect your headphones. Using Your iPod or iPhone models Alarm Clock You can use your iPod or iPhone models Alarm Clock function to automatically turn on your iPod or iPhone and the AV receiver at a specified time. The AV receiver's input source will automatically be set to the [PORT] selector. Notes: · To use this function, your iPod or iPhone must be in the UP-A1 series Dock, and the UP-A1 series Dock must be connected to the AV receiver. · When you use this function, be sure to set the AV receiver's volume control to a suitable level. · The AV receiver may take several seconds to startup, so you might not hear the first few seconds of the first song. Charging Your iPod or iPhone models Battery The UP-A1 series Dock charges your iPod or iPhone models battery while your iPod or iPhone is in the UPA1 series Dock and connected to the UNIVERSAL PORT jacks on the AV receiver. While your iPod or iPhone is seated in the UP-A1 series Dock, its battery will be charged when the AV receiver is set to "On" or "Standby". Note: When UP-A1 series Dock that seated iPod or iPhone is connected, the power consumption on standby mode slightly increases. Controlling iPod/iPhone By pressing the REMOTE MODE button that's been programmed with the remote control code for your Dock, you can control your iPod or iPhone in the Dock with the following buttons. The [PORT] button is preprogrammed with the remote control code for controlling a Dock with Universal Port connector. When Using a Dock with Universal Port connector: · Connect the Dock to the UNIVERSAL PORT jack. · See to the Dock's instruction manual for more information. You can control your iPod or iPhone when "PORT" is selected as the input source. Press [PORT] button first Note: For detailed operation of the iPod or iPhone, please refer to the instruction manual. 58 UP-A1 series Dock for iPod/iPhone--Continued Arrow [ ]/[ ] and ENTER buttons Used to navigate menus and select items. PLAYLIST [ ]/[ ] buttons Selects the previous or next playlist on the iPod or iPhone. RANDOM button Used with the shuffle function. Status messages The AV receiver is checking the connection with the dock The AV receiver do not support the connected dock UP-A1 series Dock is connected Your iPod or iPhone is properly stationed in a UP-A1 series Dock connected to the UNIVERSAL PORT jack of this unit, and the connection between your iPod or iPhone and this unit is complete. When connection is confirmed, "UP-A1" is displayed for about 8 seconds. [. . . ] Be sure to enter the appropriate remote control code first (page 84). 95 Troubleshooting--Continued Recording Can't record · On your recorder, make sure the correct input is selected. · To prevent signal loops and damage to the AV receiver, input signals are not fed through to outputs with the same name (e. g. , TV/TAPE IN to TV/TAPE OUT or VCR/DVR IN to VCR/DVR OUT). · When the Pure Audio listening mode is selected, video recording is not possible because no video signals are output. The following settings can be made for the composite video inputs You must use the buttons on the unit to make these settings. [. . . ]