User manual ONKYO PR-SC5509

[. . . ] Contents AV Controller Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PR-SC5509 Instruction Manual Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Turning On & Basic Operations . . . . . . 25 Advanced Operations . . . . . . . . . . . . . . . . . 48 Controlling Other Components. . . 77 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Thank you for purchasing an Onkyo AV Controller. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Controller. Please retain this manual for future reference. En Introduction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Audyssey Dynamic EQ Reference Level Offset provides three offsets from the film level reference (5 dB, 10 dB, and 15 dB) that can be selected when the mix level of the content is not within the standard. Note • If “Dynamic EQ” setting is set to “Off”, these technologies cannot be used. Audyssey The tone for each speaker is set automatically by Audyssey MultEQ® XT32 Room Correction and Speaker Setup. To enable the following settings, you must first perform the Room Correction and Speaker Setup (➔ page 34). • These technologies cannot be used when: – a pair of headphones is connected, or – either Pure Audio or Direct listening mode is selected. The Audyssey indicator lights. Note • If the “Audyssey” setting is set to “Off”, the “Equalizer” settings are applied (➔ page 55). • When “Audyssey Quick Start” has been used for measurement, the “Audyssey”setting cannot be selected. • Audyssey equalizing does not work with DSD sources. En 59 ■ Dynamic Volume Off Light: Activates Light Compression Mode. It quiets the loud parts, such as explosions, and boosts the quiet parts so they can be heard. Note • If you want to use Audyssey Dynamic EQ® or Audyssey Dynamic Volume® with THX listening modes, set the “Loudness Plus” setting to “Off” and set “Preserve THX Settings” to “No” (➔ page 55). • If you make Dynamic Volume active, “Dynamic EQ” is set to “On”. • When “Dynamic EQ” is set to “Off”, “Dynamic Volume” is automatically switched to “Off”. IntelliVolume ■ IntelliVolume –12dB to 0dB to +12dB in 1 dB steps. With IntelliVolume, you can set the input level for each input selector individually. This is useful if one of your source components is louder or quieter than the others. If a component is noticeably louder than the others, use e to reduce its input level. If it’s noticeably quieter, use r to increase its input level. Note • IntelliVolume does not work for Zone 2/3. A/V Sync ■ A/V Sync 0msec to 800msec in 5 msec steps. When using progressive scanning on your Blu-ray Disc/DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals. The range of values you can adjust will depend on whether your TV or display supports HDMI Lip Sync and if the “Lip Sync” setting is set to “On” or not (➔ page 68). Note • A/V Sync is disabled when the Pure Audio listening mode is selected, or when the Direct listening mode is used with an analog input source. • This setting cannot be used with the NET input selector. About Audyssey Dynamic EQ® Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Dynamic EQ selects the correct frequency response and surround levels moment-by-moment at any user-selected volume setting. The result is bass response, tonal balance and surround impression that remain constant despite changes in volume. Dynamic EQ combines information from incoming source levels with actual output sound levels in the room, a prerequisite for delivering a loudness correction solution. About Audyssey Dynamic Volume® Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of program material is being perceived by listeners in real time to decide whether an adjustment is needed. [. . . ] • If the USB device contains a lot of data, the AV controller may take a while to read it. • USB devices with security functions cannot be played. Minimum system requirements for Windows Media Player 11 on Windows XP Operating system Windows XP Home Edition (SP2), Windows XP Professional (SP2), Windows XP Tablet PC Edition (SP2), Update Rollup 2 for Windows XP Media Center Edition 2005 (KB900325), October 2006 Update Rollup for Windows XP Media Center Edition (KB925766) Processor: 233 MHz Intel Pentium II, Advanced Micro Devices (AMD), etc. Memory: 64 MB Hard disk: 200 MB of free space Drive: CD or DVD drive Modem: 28. 8 kbps Sound card: 16-bit sound card Monitor: Super VGA (800 x 600) Video card: 64 MB VRAM, DirectX 9. 0b Software: Microsoft ActiveSync (only when using a Windows Mobile-based Pocket PC or smartphone) Web browser: Microsoft Internet Explorer 6 or Netscape 7. 1 ■ Remote playback • Windows Media Player 12 • DLNA-certified (within DLNA Interoperability Guidelines version 1. 5) media server or controller device. If the operating system of your personal computer is Windows 7, Windows Media Player 12 is already installed. [. . . ]