User manual ONKYO R-801A

[. . . ] English TUNER AMPLIFIER Before using R-801A Connections Instruction Manual TUNER AMPLIFIER VOLUME Preparations Operation STANDBY STANDBY / ON DISPLAY MEMORY FM MODE INPUT TUNING PHONES CLEAR ACOUSTIC PRESENCE R- 8 01A European models front panel shown. Other Information Thank you for purchasing the ONKYO R-801A Tuner Amplifier. Please read this manual thoroughly before making any connection or turning on the power. Follow these instructions to obtain optimum performance and maximum listening enjoyment from your new R-801A. Please retain this manual for future reference. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] If the Notes · Place the unit away from strong light such as direct sunlight or inverted fluorescent light which can prevent proper operation of the remote controller. · Using another remote controller of the same type in the same room or using the unit near equipment which uses infrared rays may cause operational interference. · Do not put any object such as a book on the remote controller. The buttons of the remote controller may be pressed by mistake and drain the batteries. Placing the unit behind such doors may prevent proper remote controller operation. · If there is any obstacle between the remote controller and the remote control sensor, the remote controller will not operate. 20 Connecting the AC power cord (mains lead) TUNER AMPLIFIER VOLUME STANDBY/ON indicator STANDBY STANDBY / ON DISPLAY MEMORY FM MODE INPUT TUNING PHONES CLEAR ACOUSTIC PRESENCE R- 8 01A . Connect the AC power cord (mains lead) to the wall outlet (the mains) AC power cord (mains lead) TUNER AMPLIFIER VOLUME Notes · If the AC power cord (mains lead) is connected to the AC outlet of another component, that component's AC power cord (mains lead) must be connected to the wall outlet (the mains) to supply power to the unit. · If you do not use the unit for a long time, remove the power cord of the R-801A from the AC outlet. · The unit may cause a power surge on your home circuit when you turn it on. If this interferes with any other devices connected to the same circuit, plug this unit into another outlet on a separate circuit. STANDBY STANDBY / ON DISPLAY MEMORY FM MODE INPUT TUNING PHONES CLEAR ACOUSTIC PRESENCE R- 8 01A The STANDBY indicator ligths up. 21 Setting the Clock The "ACCUCLOCK" features an automatic clock adjusting function automatically sets the clock time by means of RDS broadcast signals. · The "ACCUCLOCK" feature is available only on the European model, and only in areas where RDS broadcasts are available. · Adjust the clock as explained in "Setting the clock manually" on page 24 if you are using U. S. or Canadian models or if you are using the unit in the area where RDS broadcasts are unavailable. · It may take about 5 minutes for the time information to be received and displayed after you plug in the power cord. After the clock is initially set, it will be adjusted periodically when the R-801A is in Standby mode. Notes on using the "ACCUCLOCK" function: · Make sure that your FM antenna has been properly connected as explained on page 18. It is strongly recommended that you install an outdoor FM antenna since the FM indoor antenna may not receive RDS broadcasts well enough to allow ACCUCLOCK to function properly. For more information, see page 25. ) · If RDS signals cannot be received, no RDS station will be found. If an RDS signal is present but the signal is not strong enough, the ACCUCLOCK cannot set the time automatically, and the indication on the display turns off. (See page 24. ) Disappear Setting the clock automatically (European models only) ACCUCLOCK starts operating as soon as the power cord is plugged in. It then searches for an RDS broadcasting station which regularly sends time signals and waits to receive such time information. "AUTO" flashes slowly on the display. flashes slowly 2. Once an RDS station that sends time signals is detected, the indicator flashes more rapidly. Adjust the clock manually. flashes rapidly 3. [. . . ] · Try to operate the remote controller from a different angle, or remove the obstruction. · The audio signal is not being input from the connected CD player or MD recorder. · Timer recording is in process. Sound is reproduced from only one speaker. The remote control doesn't operate. · The speaker cord is not connected properly or firmly, or is disconnected. · The volume level is turned down to the minimum. · The batteries in the remote controller are dead. [. . . ]