User manual ONKYO RC-632M REMOTE CONTROL CODES

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Otherwise, appropriate CEC (Consumer Electronics Control) operation will not be guaranteed. If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign "OPT1" to the "TV/CD" input selector. Here are the default assignments. Input selector BD/DVD VCR/DVR CBL/SAT GAME AUX TV/CD PORT Default assignment COAX --------OPT1 ----OPT2 ----- En BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/ CD, PORT COAX, OPT1, OPT2: Select a corresponding digital audio input that the component has been connected. - - - - -: Select if the component is connected to an analog audio input. 28 Note · When an HDMI IN is assigned to an input selector in "HDMI Input" ( 28), this input assignment is automatically set to the same HDMI IN. And in addition to the usual inputs (e. g. , COAX, etc. ), you can also select HDMI inputs. · Available sampling rate for PCM signals from a digital input (optical and coaxial) is 32/44. 1/48/88. 2/96 kHz/16, 20, 24 bit. · If you connect a component (such as UP-A1 Dock that seated iPod) to the UNIVERSAL PORT jack, you cannot assign any input to PORT selector. Sp Config (Speaker Configuration) Menu Sp Config Crossover (Crossover Frequency) This setting is advantageous for the speakers that you specified as "Small" in the "Sp Config (Speaker Configuration)" ( 29). To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your speakers. 40Hz, 50Hz, 60Hz, 80Hz, 100Hz, 120Hz, 150Hz, 200Hz: Use the diameter of the smallest speaker in your system when choosing the crossover frequency. Speaker cone diameter Over 8 in. (9 cm) * Crossover frequency 40/50/60 Hz* 80 Hz 100 Hz 120 Hz 150/200 Hz* This section explains how to specify which speakers are connected and their sizes. For speakers with a cone diameter larger than 6-1/2 inches (16 cm), specify Large Cone diameter (full band). This setting controls the front left, right, and center mix, allowing you to adjust the weight of the center channel sound. Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. Left, Center*1, Right, Surround Right, Surround Left ­12 dB to 0 dB to +12 dB in 1 dB step. Subwoofer*1 ­15 dB to 0 dB to +12 dB in 1 dB step. Note · Speakers that you set to "No" or "None" in the "Sp Config (Speaker Configuration)" ( 29) cannot be selected. · The speakers cannot be calibrated while a pair of headphones is connected, Speakers B is on, or "Audio TV OUT" setting is set to "On" ( 31) or the AV receiver is muted. *1 For the center speaker and subwoofer, the level settings made by using AUDIO are saved. Tip · If you're using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading. Audio Adjust Menu Audio Adjust With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. Multiplex/Mono Settings Multiplex This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on. En 30 DTS Setting Neo:6 Music Center Image 0 to 2 to 5 With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. Sound is spread in left and right (the outside) so that the set value is made big. Please adjust by liking. . Hardware Menu Hardware Remote Control Settings Remote ID 1, 2, or 3 When several Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can change its remote ID from "1", to "2" or "3". Note · If you do change the AV receiver's remote ID, be sure to change the remote controller to the same ID (see below), otherwise, you won't be able to control it with the remote controller. Theater-Dimensional Setting Listening Angle Wide: Select if the listening angle is 40 degrees. With this setting, you can optimize the Theater-Dimensional listening mode by specifying the angle of the front left and right speakers relative to the listening position. [. . . ] For -compatible players/recorders The following link operation is possible by connecting the AV receiver to an -compatible player/recorder. · When the playback is started on the player/recorder, input of the AV receiver will switch to the HDMI input of the player/recorder that is playing back. · Operation of the player/recorder is possible with the remote controller supplied with the AV receiver. * Not all functions may operate depending on the model. En 49 How to connect and setup 1 3 Confirm the connecting and setting. Connect the HDMI OUT jack to the HDMI input jack of the TV. Blu-ray Disc/DVD player, etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. [. . . ]