User manual ONKYO RDC-7.1

[. . . ] AV Controller RDC-7. 1 Instruction Manual WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] Using the [ ] and [ ] cursor buttons, select the menu that you want to enter. Use the [ ] and [ ] cursor buttons to select the sub-menu that you want to enter and press the [Enter] button. Each sub-menu has different settings that can be changed as desired, and they are all explained in the pages that follow. To change a setting, first select it using the [ ] and [ ] cursor buttons, and then change the setting using the [ ] and [ ] cursor buttons. Press the [Return] button to set the new settings and return to the previous menu. 7 PQRS 8 TUV 9 WXYZ T V VOL +10 --/--- 0 Clear # Direct Tuning Custom Zone 3 3 Zone 2 Macro Scroll wheel Mode Input Zone 2 4 5 Dimmer TV Input Top Sleep Men u Men u Aud io A + CH Disc rver Se DJ Enter VOL E xi t Prev CH Display id e Gu Re turn p Setu Muting Setup/ Enter/ Return/ /// 6 Main A, Main B Rec Main A Main B Random Audio Surround Repeat Pure A Repeat Test Tone Playlist Subtitle THX A-B Direct Video CH SEL Album Audio SEL Angle Last Memory All CH ST Search DSP Music Level Ar tist L Night Language Stereo Memory DSP Photo Level + Genre Re-EQ Location Caps Delete RC-554M RC-555M 7 1 90 Press the scroll wheel when using the remote controller. When setting on the RDC-7. 1, use the [Setup] button, the [ ]/[ ]/[ ]/[ ] buttons and the [Enter] button. In addition, the [Exit] button is used instead of the [Return] button. Hardware Setup In this section, you will perform the initial settings for the following scenarios. · When you want to change the RDC-7. 1's remote control ID. · When you want to fix the AM Frequency Step setting to 9 kHz or 10 kHz. Remote Control Setup Sub-menu Remote ID This section explains how to change the RDC-7. 1's remote control ID. You may need to change this if the RDC-7. 1's remote controller interferes with other IntegraRESEARCH components located in the same room. If you change the RDC-7. 1's remote control ID, be sure to select the same ID for the remote controller (See page 142). Note: It is recommended that you perform setup using the [Setup]/[ ]/[ ]/[ ]/[ ]/[Exit] buttons of the RDC-7. 1's front panel. If the remote controller is used for setup, signals from the remote controller will not be received just after the remote control ID settings have been changed (See "Changing the Remote Controller's Control ID" on page 142 to change the remote control ID for the remote controller). AM Frequency Setup Sub-menu (Asian and Australian Models Only) Frequency Step The setting in this sub-menu determines the incremental or decremental amount when adjusting the AM tuner frequency. The initial setting is 9 kHz, and this only needs to be changed if you are using the RDC-7. 1 in a 10 kHz region. 10 kHz: Select if 10 kHz increments are used in your area. TV Format Sub-menu TV Format (for all models other than USA and Canadian models) The settings in the TV Format sub-menu can be configured for Main B and Zone 2 as well as for Main A. When you want to reconfigure the settings to conform to the television format used in the area where you use the RDC-7. 1, use this sub-menu so that no time is wasted on detection. When you leave this setting unchanged, the television format is detected and automatically set by the RDC-7. 1. NTSC: Use this setting when you know the television format is NTSC. 91 Setup Menu Speaker/Output Setup The RDC-7. 1 provides a wide range of variations in speaker connections and speaker settings, so you have to specify speaker settings according to conditions of each variation. For proper selection of an AV device connected at switching of the input type, you also need to allocate "audio output" and "video output" to each input type. If this allocation is incorrect, the desired component will not play a selected input source. Please setup correctly by referring to the information you wrote down in the Your System Setting booklet. Speaker Configuration Sub-menu Specify the rooms where you want to use speakers. Note: Basically, a speaker set with the maximum number of speakers should be assigned to the Speaker A and configured for main room A (Main A). When either the center, surround, or surround back speakers are not configured to the Speaker A terminals, or any of these speakers is set to "Not Used" in the Speaker A settings, you cannot perform the settings for the corresponding speakers configured to the Speaker B. [. . . ] "Only available with Dolby D" · Can be used with only Dolby Digital. "Not available with this signal" · Doesn't work with the current listening mode. "Not available with Muting" · Operation not allowed because the RDC-7. 1 is currently muted. "Not available in this Listening Mode" · Doesn't work with the current listening mode. [. . . ]