User manual ONKYO SKF-330F

[. . . ] 2 5. 1ch Home Theater System HT-S580 AV Receiver (HT-R330) Front Speakers (SKF-330F L/R) Center Speaker (SKC-330C) Surround Speakers (SKM-330S L/R) Subwoofer (SKW-330) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Instruction Manual Basic Operation Playing your AV components . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new 5. 1ch Home Theater System. [. . . ] Setup closes. TESTING THE SPEAKERS To test that all of the speakers are working properly, press the remote controller's [TEST TONE] button. The test tone will be output by each speaker in turn and the name of each speaker will appear on the display. · If the test tone is not produced by a speaker, or it's produced by a speaker other than that shown on the display, you may have wired the speakers incorrectly and you should check your connections (see page 18). · If the test tone is not produced by a speaker and its name does not appear on the display, you may have set the speaker settings incorrectly (see page 34). 35 Playing Your AV Components Basic AV Receiver Operation 2 STANDBY/ON DISPLAY TUNING / PRESET 4 1 MASTER VOLUME ENTER ON STANDBY REMOTE MODE RECEIVER TAPE/AMP DVD 1 INPUT SELECTOR 1 V1 2 V2 3 V3 CD 4 7 TAPE TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP 5 MULTI CH 6 DVD MD STANDBY 8 TUNER 9 CD CDR A SPEAKERS B +10 --/--CD 0 DIMMER CLR SLEEP CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER DISC CH VOL 4 MULTI CH 1 2 TOP MENU MENU SP A / B MUTING ENTER 1 AV receiver DVD VIDEO 1/VCR VIDEO 2 Remote controller Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1/VCR, VIDEO 2, and VIDEO 3 input sources respectively. VIDEO 3 TAPE TUNER CD 2 AV receiver A SPEAKERS B Remote controller Use the SPEAKERS [A] and [B] buttons on the AV receiver or the [SP A/B] button on the remote controller to select the speaker set that you want to use. Pressing the remote controller's [SP A/B] button cycles through the following settings: Speaker Set A Speaker Set A&B Speaker Set B Off. The A and B speaker indicators show whether each speaker set is on or off. Indicators Note that when speaker set B is turned on, speaker set A is reduced to 2. 1-channel playback. When you select DVD or another video component, on your TV you'll need to select the video input that's connected to the AV receiver's MONITOR OUT. 3 4 AV receiver MASTER VOLUME Remote controller VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The AV receiver is designed for home theater enjoyment and has a wide volume range for precise adjustment. 5 Select a suitable listening mode and enjoy!See page 44. 36 Playing Your AV Components--Continued Displaying Source Information ON STANDBY REMOTE MODE RECEIVER TAPE/AMP DVD RECEIVER INPUT SELECTOR You can display various information about the current input source as follows. Press the [RECEIVER] button, and then press the [DISPLAY] button repeatedly to cycle through the available information. 1 V1 2 V2 3 V3 CD MULTI CH 4 7 TAPE 5 MULTI CH 6 DVD MD 8 TUNER 9 CD CDR +10 --/--- 0 DIMMER CLR SLEEP DISC CH VOL LISTENING MODE STEREO SURROUND The following information can typically be displayed for input sources. LEVEL+ AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE LEVEL- Input source & volume Signal format* or sampling frequency Input source & listening mode DISPLAY DISPLAY OR-EQ L NIGHT CINE FLTR RC-606S Using the Multichannel Input The multichannel input is for connecting a component with individual 5. 1-channel analog audio output jacks, such as a DVD player or MPEG decoder. Press the [RECEIVER] button followed by the [MULTI CH] button so that MULTI CH indicator appears on the display. Audio from the multichannel input will now be used for the DVD input source. MULTI CH indicator *If the input signal is analog, no format information is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about three seconds, then the previously displayed information reappears. Interpreting Surround Channel Information A BC A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). If there's surround back channel information, this number will be 3. C: LFE channel for subwoofer (1 means yes). Note: · While the multichannel input is selected, the Speaker Configuration settings on page 34 are ignored, and signals from the multichannel input are fed to the front left, front right, center, surround left, and surround right speakers and subwoofer regardless of those settings. 37 Using the Tuner Listening to the Radio TUNING MODE TUNING TUNING / PRESET Tuning into Radio Stations Auto Tuning Mode 1 TUNING MODE MASTER VOLUME STANDBY/ON ENTER Press the [TUNING MODE] button so that the AUTO indicator appears on the display. STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD 2 TUNING / PRESET TUNER ENTER Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. With the built-in tuner, you can enjoy AM and FM radio stations. [. . . ] · If nothing improves the reception, install an outdoor antenna. 54 Troubleshooting--Continued Remote Controller The remote controller doesn't work?· Make sure that the batteries are installed with the correct polarity (page 7). · Make sure that the remote controller is not too far away from the AV receiver, and that there's no obstruction between the remote controller and the AV receiver's remote control sensor (page 7). · Make sure you've selected the correct remote controller mode (page 12). [. . . ]