User manual ONKYO SKS-HT518

[. . . ] Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Use only with the cart, stand, PORTABLE CART WARNING tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. [. . . ] To prevent this, place the supplied pads underneath the subwoofer's feet. The pads also provide a stable base for the subwoofer. SKW-518 SKW-501 With the Auto Standby function, the SKW-518/ SKW-501 automatically turns on when an input signal is detected in Standby mode. When there's no input signal for a while, the SKW-518/SKW-501 automatically enters Standby mode. E OUTPUT LEVEL control This control is used to adjust the volume of the subwoofer. F LINE INPUT This RCA input should be connected to the subwoofer pre out on your AV receiver with supplied RCA cable. Note: The Auto Standby function turns the subwoofer on when the input signal exceeds a certain level. If the Auto Standby function does not work reliably, try slightly increasing or decreasing the subwoofer output level on your receiver. Pad 5 Connecting the Speakers Read the following before connecting your speakers: · Turn off your receiver before making any connections. Connect positive (+) terminals to only positive (+) terminals, and negative (­) terminals to only negative (­) terminals. If the speakers are wired incorrectly, the sound will be out of phase and will sound unnatural. Doing so may damage your amp. Connecting the Speaker Cables Use the supplied cables to connect each speaker's input terminals to the corresponding speaker output terminals on your receiver. To make a connection, while pressing the terminal lever, insert the wire into the hole, and then release the lever. Make sure that the terminals are gripping the bare wires, not the insulation. Front Left Subwoofer Surround Right Surround Left Center Front Right Gray Blue White Green Red * HDMI ASSIGNABLE IN 3 IN 2 IN 1 OUT SURR SPEAKERS FRONT SPEAKERS L Y L DIGITAL IN (DVD) COMPONENT VIDEO AM 1 COAXIAL (CBL/SAT) CB/PB CBL/SAT V VCR/DVR DVD MONITOR OUT V CENTER SPEAKER 2 R R ANTENNA FM 75 CR/PR (VCR/DVR) 1 S IN 2 IN 1(DVD) ASSIGNABLE S IN OPTICAL (CD) OUT OUT IN OUT OUT IN IN IN FRONT SURR CENTER 2 IN IN PRE OUT ASSIGNABLE L L L SUB WOOFER R REMOTE CONTROL R SUB WOOFER R CD TAPE CBL/SAT VCR/DVR DVD * Using the supplied RCA cable, connect the subwoofer's LINE INPUT to your AV receiver's SUBWOOFER PRE OUT. 6 Connecting the Speakers--Continued Enjoying Home Theater The Home Theater means that you can enjoy surround sound with a real sense of movement in your own home--just like being in a movie theater or concert hall. Front left and right speakers (SKF-518F) These output the main sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward slightly so as to create a triangle, with the listener at the apex. Surround left and right speakers (SKM-518S) These speakers are used for precise sound positioning and to add realistic ambience. Position them at the sides of the listener, or slightly behind, about 60­ 100 cm above ear level. Center speaker (SKC-518C) Keyhole slots for wall mounting Using the Rubber Stoppers for a More Stable Platform We recommend using the provided rubber stoppers to achieve the best possible sound from your speakers. The rubber stoppers prevent the speakers from moving, providing a more stable platform. Use thick stoppers for the center speaker, and thin stoppers for the other speakers. Thin rubber stoppers Thick rubber stoppers 217 mm Caution: A mounting screw's ability to support a speaker depends on how well it's anchored to the wall. If there are no studs, or the walls are solid, use suitable wall anchors. Use screws with a head diameter of 9 mm or less and a shank diameter of 4 mm or less. With hollow walls, use a cable/pipe detector to check for any power cables or water pipes before making any holes. Bottom of the SKF518F Bottom of the SKM518S Thick rubber stoppers 55 mm Bottom of the SKC-518C 12 mm 8 Power Cord Precautions · Before connecting the power cord, connect all of your speakers and AV components. · Turning on the SKW-518 (HTP-518)/SKW-501 (SKS-HT518) may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. [. . . ] The RCA cable is not properly connected to the subwoofer's LINE INPUT. External interference from a TV or other electronic device is being picked up. 10 Specifications Powered Subwoofer (HTP-518: SKW-518) Type: Power Supply: Power Consumption: Input sensitivity/impedance: Maximum output power: Frequency response: Cabinet capacity: Dimensions (W × H × D): Weight: Drivers unit: Other: Bass-reflex AC 230 V/50 Hz 105 W 140 mV/20 k 90 W 27 Hz­150 Hz 24. 2 L 230 × 425 × 383 mm (incl. projection) 9. 4 kg 20 cm Cone Auto Standby function Center Speaker (SKC-518C) Type: Input sensitivity/impedance: Maximum input power: Output sound pressure level: Frequency response: Crossover frequency: Cabinet capacity: Dimensions (W × H × D): Weight: Speaker: Terminal: Keyhole slot: Threaded insert: Grille: Other: 2 Way Bass-reflex 8 130 W 78 dB/W/m 60 Hz­50 kHz 4 kHz 1. 8 L 273 × 101 × 106 mm (incl. grille and projection) 1. 1 kg 8 cm Cone Woofer 2. 5 cm Balanced Dome (Tweeter) Spring type color coded 2 5 mm screw, Depth 8 mm × 1 Fixed Magnetic shielding Powered Subwoofer (SKS-HT518: SKW-501) Type: Power supply: Power consumption: Input sensitivity/impedance: Maximum output power: Frequency response: Cabinet capacity: Dimensions (W × H × D): Weight: Drivers unit: Other: Bass-reflex AC 220-240 V, 50/60 Hz 105 W 140 mV / 20 k 90 W 27 Hz­150 Hz 24. 5 L 230 × 425 × 412 mm (incl. [. . . ]