User manual ONKYO SKW-530

[. . . ] 2 7. 1ch Home Theater System HT-S780 AV Receiver (HT-R530) Front Speaker (SKF-530F) Center Speaker (SKC-530C) Surround Speaker (SKM-530S) Surround Back Speaker (SKB-530) Powered Subwoofer (SKW-530) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Instruction Manual Basic Operation Playing your AV components . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new 7. 1ch Home Theater System. [. . . ] Because our ears are less sensitive to very low bass sounds, there's a temptation to set the level of the subwoofer too high. As a rule of thumb, set the subwoofer level to what you think is the optimal level, and then back it off slightly. See page 40. 3 4 AV receiver MASTER VOLUME Remote controller VOL 5 34 Playing Your AV Components--Continued Displaying Source Information ON STANDBY REMOTE MODE RECEIVER TAPE/AMP DVD MD RECEIVER INPUT SELECTOR You can display various information about the current input source as follows. Press the [RECEIVER] button, and then press the [DISPLAY] button repeatedly to cycle through the available information. 1 V1 2 V2 3 V3 CD CDR MULTI CH 4 7 TAPE 5 MULTI CH 6 DVD TV 8 TUNER 9 CD VCR +10 10 --/--- 0 CLR 11 SLEEP SAT 12 CABLE DIMMER TV INPUT VOL DISC CH VOL LISTENING MODE STEREO SURROUND The following information can typically be displayed for input sources. LEVEL+ DVD CINE FLTR AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE LEVELHDD L NIGHT Input source & volume Signal format* or sampling frequency Input source & listening mode DISPLAY DISPLAY OR-EQ RC-608M Using the Multichannel Input The multichannel input is for connecting a component with individual 5. 1-channel analog audio output jacks, such as a DVD player or MPEG decoder. Press the [RECEIVER] button followed by the [MULTI CH] button so that MULTI CH indicator appears on the display. Audio from the multichannel input will now be used for the DVD input source. MULTI CH indicator *If the input signal is analog, no format information is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about three seconds, then the previously displayed information reappears. Interpreting Surround Channel Information A BC A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). If there's surround back channel information, this number will be 3. C: LFE channel for subwoofer (1 means yes). Note: · While the multichannel input is selected, the Speaker Configuration settings on page 48 are ignored, and signals from the multichannel input are fed to the front left, front right, center, surround left, and surround right speakers and subwoofer regardless of those settings. 35 Using the Tuner Listening to the Radio TUNING MODE TUNING TUNING / PRESET Tuning into Radio Stations Auto Tuning Mode 1 TUNING MODE MASTER VOLUME STANDBY/ON ENTER Press the [TUNING MODE] button so that the AUTO indicator appears on the display. STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP CLEAR VIDEO 3 INPUT PHONES PURE AUDIO MULTl CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD VIDEO L AUDIO R VCR 2 TUNING / PRESET TUNER ENTER Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. With the built-in tuner, you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. 1 TUNER Use the [TUNER] input selector button to select either AM or FM. In this example, FM has been selected. When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator appears on the display, as shown. TUNED AUTO Band Frequency FM STEREO (Actual display depends on country. ) Manual Tuning Mode AM Frequency Step Setup (not North American model) Here you can specify the AM frequency step used in your area. When this setting is changed, all radio presets are deleted. 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. 1 Press the [SETUP] button and use the Up and Down [ ]/[ ] buttons to select "0. Use the Up and Down [ ]/[ ] buttons to select "AM Freq, " and then use the Left and Right [ ]/[ ] buttons to select: 10 kHz: Select if 10 kHz steps are used in your area. Setup closes. 2 TUNING / PRESET ENTER 2 Press and hold the TUNING Up or Down [ ]/[ ] button. Press the buttons repeatedly to change the frequency one step at a time. The American model changes FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For other models it's 0. 05 MHz steps for FM and 9 kHz steps for AM. Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. [. . . ] · To control Onkyo components via , point the remote controller at the AV receiver. · To control Onkyo components without , or other manufacturers' components, point the remote controller at that component. · The display is turned off when the Pure Audio (not North American model) listening mode is selected. · To use , you must make an connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally (page 31). The AV receiver contains a microcomputer for signal processing and control functions. [. . . ]