User manual ONKYO SKW-550

[. . . ] 2 7. 1ch Home Theater System HT-SR800 AV Receiver (HT-R550) Front Speakers (SKF-550F) Center Speaker (SKC-550C) Surround Speakers (SKM-550S) Surround Back Speakers (SKB-550) Powered Subwoofer (SKW-550) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Instruction Manual Basic Operation Playing your AV components . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new 7. 1ch Home Theater System. [. . . ] Refer to the relevant manuals. 41 Playing Your AV Components Basic AV Receiver Operation MULTI CH 1 TUNING PRESET 4 MASTER VOLUME STANDBY/ON REMOTE MODE RECEIVER TAPE/AMP DVD M D/CDR 1 Subwoofer's rear panel 1 INPUT SELECTOR 1 VCR/DVR 2 CBL/SAT 3 6 DVD CD DOCK STANDBY/ON 4 AUX 5 MULTI CH TV STANDBY 7 TAPE 8 TUNER 9 CD VCR 12 CABLE 10 MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP ENTER RETURN 11 +10 D TUN AUX INPUT 0 ENT DIMMER CLR SLEEP SAT --/--R PHONES SETUP MIC VIDEO L AUDIO 4 4 MIN MAX A SPEAKERS B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE CLEAR TV INPUT GUIDE TOP MENU VOL DISC ALBUM CH VOL 2 DISPLAY 2 PREVIOUS MENU OUTPUT LEVEL SP A / B MUTING ENTER PLAYLIST/CAT PLAYLIST/CAT 1 AV receiver DVD VCR/DVR CBL/SAT Remote controller RECEIVER Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] REMOTE MODE button, and then use the INPUT SELECTOR buttons. 1 AUX TAPE TUNER VCR/DVR 2 CBL/SAT 4 CD AUX 6 DVD 7 TAPE 8 TUNER 9 CD 2 AV receiver A SPEAKERS B Remote controller To turn the speakers on or off, use the AV receiver's SPEAKERS [A] and [B] buttons, or use the remote controller's [SP A/B] button. Pressing the remote controller's [SP A/B] button cycles through the following settings: Speaker Set A Speaker Set A&B Speaker Set B Off. Note that while speaker set B is on, speaker set A is reduced to 5. 1-channel Indicators playback. See page 5 for more information about speaker sets A and B. 3 Start playback on the source component. To watch a DVD or other video source, on your TV, select the video input that's connected to the AV receiver's MONITOR OUT jack. If your TV is connected to the HDMI OUT, see the tip on page 29. Remote controller 4 AV receiver MASTER VOLUME VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. Since the AV receiver is designed for home theater enjoyment, it has a wide volume range for precise adjustment. Because our ears are less sensitive to very low bass sounds, there's a temptation to set the level of the subwoofer too high. As a rule of thumb, set the subwoofer level to what you think is the optimal level, and then back it off slightly. 5 42 Select a suitable listening mode and enjoy!See "Using the Listening Modes" on page 48. Playing Your AV Components--Continued Displaying Source Information STANDBY/ON REMOTE MODE RECEIVER TAPE/AMP DVD M D/CDR RECEIVER INPUT SELECTOR You can display various information about the current input source as follows. RECEIVER 1 VCR/DVR 2 CBL/SAT 3 6 DVD CD DOCK MULTI CH 4 AUX 5 MULTI CH TV 7 TAPE 8 TUNER 9 CD VCR 12 CABLE 10 11 +10 D TUN 0 ENT DIMMER CLR SLEEP SAT --/--- DISPLAY VOL Press the [RECEIVER] REMOTE MODE button, and then press the [DISPLAY] button repeatedly to cycle through the available information. TV VOL DISC ALBUM CH The following information can typically be displayed: LISTENING MODE STEREO SURROUND AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE LEVELLEVEL+ Input source & volume*1 Signal format*2 or sampling frequency Input source & listening mode DISPLAY DISPLAY VCR L NIGHT DVD CINE FLTR HDD RC-681M Using the Multichannel DVD Input The multichannel DVD input is for connecting a component with a 7. 1-channel analog audio output, such as a DVD-Audio or SACD-capable DVD player, or an MPEG decoder. See page 28 for hookup information. RECEIVER *1 When AM or FM radio is used, the band, preset number, and frequency are displayed. *2 If the input signal is analog, or AM or FM radio is selected, no format information is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears. Note: · The listening mode is displayed only when speaker set A is on. Interpreting Surround Channel Information Press the [RECEIVER] REMOTE MODE button, followed by the [MULTI CH] button. The MULTI CH indicator appears on the display. MULTI CH indicator MULTI CH A BC Audio from the multichannel DVD input will now be used for the DVD input source. Note: · While the multichannel DVD input is selected, the Speaker Configuration settings on page 56 are ignored, and signals from the multichannel input are fed to the speakers as they are. A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). If there's surround back channel information, this number will be 3. C: LFE channel for subwoofer (1 means yes). 43 Listening to the Radio Listening to AM/FM Stations TUNER TUNING MASTER VOLUME STANDBY/ON Tuning into AM/FM Radio Stations Auto Tuning Mode 1 TUNING MODE TUNING PRESET Press the [TUNING MODE] button so that the AUTO indicator appears on the display. STANDBY MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP ENTER RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R A SPEAKERS B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE CLEAR 2 TUNING PRESET TUNING MODE Press the TUNING Up or Down [ ]/[ ] button. [. . . ] Make sure all of your speakers are working properly. Remote Controller The remote controller doesn't work · Make sure that the batteries are installed with the correct polarity (page 13). · Make sure that the remote controller is not too far away from the AV receiver, and that there's no obstruction between the remote controller and the AV receiver's remote control sensor (page 13). · Make sure you've selected the correct remote controller mode (page 14). · Make sure you've entered the correct remote control code (page 62). [. . . ]